Assume a MARIE assembly program has an instruction JNS Subr stored at hex address 108 and symbol table has one entry Hex Label Address Subr 200 After execute the instruction JNS Subr at hex address 108, the content of memory at address 200 is and the hex value of PC is

Assume a MARIE assembly program has an instruction JNS Subr stored at hex address 108 and symbol table has one entry Hex Label Address Subr 200 After execute the instruction JNS Subr at hex address 108, the content of memory at address 200 is and the hex value of PC is

Name: Assume a MARIE assembly program has an instruction JNS Subr stored at
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Assume a MARIE assembly program has an instruction JNS Subr stored at hexaddress 108 and symbol table has one entryHexLabelAddressSubr200After execute the instruction JNS Subr at hex address 108, the content of memory ataddress 200 isand the hex val

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 2 Address Machine Code Ox150 OXE008 Determine the next Program Counter (PC) in hex if flags C, Z, N are set when the above instruction finish executing.
Assume that the instruction pointer, EIP, contains 9810 and the assembly language representation of the instruction in memory at address 9810 is JAE 131. If the flags are currently CF=1, ZF=0 and SF=0 what is the value of the EIP after the instruction executes? The answer 102 is not correct so what is the correct answer?
Assume that the instruction pointer, EIP, contains 10410 and the assembly language representation of the instruction in memory at address 10410 is JNE 59. If the flags are currently CF=1, ZF=0 and SF=1 what is the value of the EIP after the instruction executes?
The content of AC in the basic computer is hexadecimal A937 and the initial value of E is 1. Determine the contents of AC, E, PC, AR, and IR in hexadecimal after the execution of the CLA instruction. Repeat 11 more times, starting from each one of the registers reference instructions. The initial value of PC is hexadecimal 021.
Q2:- (A) Find the phicycal address if (BP) = 0100H , (SI) = 0200H , (SS) = 2000H and a displacement of 10H, of the instruction MOV AL, [BP+SI+10H]. Which the name of Addressing Modes?
Translate the below C code into RISC-V architecture, assuming that the values of i and j are placed in registers x23 and x24 respectively. The base address of array B is in register x30, and the base address of array C is in register x31. C[7] = B[i+j];
For each of the following sets of RISC-V assembly instructions below, identify any data hazards that occur and indicate which type (i.e., EX hazard 1a or 1b, MEM hazard 2a or 2b, or load-use hazard) of hazard has occurred. You can specify where the hazard has occurred by indicating which instruction (i.e., the first instruction, second instruction, etc.) will experience the hazard. x11, 0(x6) x12, 8(x6) add x20, x11, x12 x20, 0(x6) x13, 16(x6) add x20, x20, x13 x20, 8(x6) ld ld sd ld sd
What is the clock period of a pipelined MIPS architecture with two stages, one with Instruction Fetch, Decode, and Execute and the other with Memory and Write Back? Assume that memory and ALU take 2ns, and that registers and other logic take Ins or less.
Create a multi-clock-cycle diagram for the set of RISC-V assembly instructions below. Assume that the datapath implements forwarding and mark all instances where forwarding occurs on the diagram. ld x12, 32(x8) ld x13, 40(x8) add x14, x10, x12 add x14, x13, x14 sd x14, 0(x9)
Indirect Addressing Mode Instruction 002A J@ RETADR 3E2003 0030 RETADR RESW 1 Instruction Starts with 002A Opcode of J is 3C Object code is 3E2003 Show the detail work to get the above object code from the instruction. F9 F10 F11 F12 delet + ||
SP=1239H, SS=9876H, the physical address is AAAFOH Non of them 1BC06H 0AAAFH 99999H if BX=1000, DS=0400, and AL=EDH, for the following instruction: MOV [BX] + 1234H, AL. the physical address is 6324H O 4244H 4234H 6234H 6243H O
Write a code segment in MARIE assembly to do the following: If X<Y, then X=Y+X; If X>Y Y=2*X