As seen in the figure, the block on an inclined plane is lifting from 0 0 with two degrees increment in each step. (8, 0, 0, = 2, 02 4, ..) Until which degree can we increase the angle without any slipping between the block and the inclined plane? For condition of F, > F, , the block continues to hang on the inclined plane. Otherwise, it starts to slip. F = W• sine(rad), Fy = W• cos®(rad) F. = F,• u, µ = 0.50, W = 100 N %3D

As seen in the figure, the block on an inclined plane is lifting from 0 0 with two degrees increment in each step. (8, 0, 0, = 2, 02 4, ..) Until which degree can we increase the angle without any slipping between the block and the inclined plane? For condition of F, > F, , the block continues to hang on the inclined plane. Otherwise, it starts to slip. F = W• sine(rad), Fy = W• cos®(rad) F. = F,• u, µ = 0.50, W = 100 N %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
In the graph the force versus displacement of a spring is given (the spring is shown in a separate figure--see below). The x-axis range is ±2 cm. The y-axis range is tFs, where Fs = 220 N. How much work does the spring do on the block (the mass "m") when the block moves from x₁ = 7.6 cm to 4.3 cm? W J y F. X -1.5 -0.5 0 10.5 1 1.5 -F How much work does the spring do on the block (the mass "m") when the block moves from x; = 7.6 cm to -7.6 cm? W = Question Help: Read Submit Question m
Solve for Problem 2, when RN1 = 0145
Statics an 2.18 A 200# stone is being lifted off the ground by a lev- ering bar. Determine the push P required to keep the stone in the position shown. Varignon's Theorem The French mathematician Pierre Varignon developed a very important theorem of statics. It states that the mo- ment of a force about a point (axis) is equal to the algebraic 1W=200* 3011 36" 47
Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
The crane arm in the figure lifts the 95 kg mass at the end. When the angle BC piston makes with the horizontal is at the position 8= 0°, which of the following is the force acting on the BC piston in N? 785 mm 340 110 mm mm 360 mm Lütfen birini seçin: a. 3248.83 b. 4241.51 C. 6107.74 d. 2214.24
A force of 80 N is applied to the handle of the press shown in the figure, which causes a downward vertical force to be applied to the ball E by the block (you can assume that the block slides vertically with no friction. F 80 N 70 Determine the magnitude of the vertical force, and the mechanical advantage of this machine. 40 mm 60 Note: A, B, C, D, and F are pins. 400 mm Draw all FBD's needed to solve, show all work, and put units on your answers.
GIVEN: W= 595 N GIVEN: ANGLE A= 44 DEGREE GIVEN: ANGLE B= 14 DEGREE ANSWER: SOLVE (A) magnitude P in Newton SOLVE (B) reaction Oy in Newton SOLVE (C) reaction Ox at point O in Newton PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY AND SHOW THE FREE BODY THE DIAGRAM. PLS SOLVE IN EQUILIBRIUM PLS SOLVE COMPLETE SOLUTION.
Suppose that F1 = 19 kN. a) Determine the x and y components of reaction at pin A using scalar notation. b) Determine the x and y components of reaction at pin D using scalar notation.
Use the drawing below to answer the following two questions. a. Determine the equivalent spring stiffness of the following system. Simplify the expression (ie – single common denominator. Your answer should be an expression of just K’s – no numbers). b. If the weight on top is 20 lb and the K1 = K4 = 50 lb/in, K2 = 33 lb/in and K3 = K5 = 25 lb/in, what is the natural frequency of the system?
Q1: Draw just the Free Body Diagram of the following figures. D Figure (1) Figure (2) Figure (3) T 30° 45° 60° - Figure (4) Figure (5) 26 kN 250 N 30 13 12 30 0.15 m 0.4 m B. 0 m 2 m 4 m
The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter of 12cm,spring wire diameter is 6mm. Find the spring inside diameter. Select one: O a. 114 mm O b. 52mm O c. 150mm O d. 20mm