Análisis de rectificador onda completa Consider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis: (a) Rig up the circuit as shown in Figure land plot V and i versus time. (b) Why is there ringing on the current wave-form? (c) What is the series impedance of the circuit? (d) Plot V, and V. versus time, What is the ripple? How does ripple depend on load, capacitor C, and frequency of input wave-form? (e) Measure the current and voltage waveform across the rectifier diode. (f) Estimate the average and ms currents through the rectifier diode, Calculate the diode power dissipation. (g) What should be the peak current rating of the diode? (h) Change the initial charge voltage on the capacitor Cr. What is the effect on the input surge current? (i) Change the phase angle of the input V, at start up. Observe the effect on current i. What happens and why? 0) Under what conditions do you get maximum peak current to flow through the diodes (k) Measure the input voltage and current and estimate the power factor. (1) What is the effect of change in C, value on the input current and power factor? (m) Choose a suitable value for R and construct a simulation model in LTspice and verify your analytic results.

Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
icon
Related questions
Question
9.
9.
R
V.
Figure 1. Single-phase capacitor-fi Iter rectifier circuit.
Transcribed Image Text:9. 9. R V. Figure 1. Single-phase capacitor-fi Iter rectifier circuit.
Análisis de rectificador onda completa
Consider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis:
(a) Rig up the circuit as shown in Figure land plot V andi versus time.
(b) Why is there ringing on the current wave-form?
(c) What is the series impedance of the circuitệ
(d) Plot V and V. versus time. What is the ripple? How does ripple depend on load, capacitor C; and frequency of input wave-form?
(e) Measure the current and voltage waveform across the rectifier diode.
(f) Estimate the average and ms currents through the rectifier diode, Calculate the diode power dissipation.
(g) What should be the peak current rating of the diode?
(h) Change the initial charge voltage on the capacitor Cr. What is the effect on the input surge current?
(i) Change the phase angle of the input V, at start up. Observe the effect on current i. What happens and why?
1) Under whaf conditions do you get maimum peak current to flow through the diodes?
(k) Measure the input voltage and current and estimate the power factor.
(1) What is the effect of change in Cr value on the input current and power factor?
(m) Choose a suitable value for R and construct a simulation model in LTspice and verify your analytic results.
Transcribed Image Text:Análisis de rectificador onda completa Consider the capacitor-filter rectifier circuit as shown in Figure 1. The input is a single-phase source that is derived from a 220 Vrms mains. Tasks for analysis: (a) Rig up the circuit as shown in Figure land plot V andi versus time. (b) Why is there ringing on the current wave-form? (c) What is the series impedance of the circuitệ (d) Plot V and V. versus time. What is the ripple? How does ripple depend on load, capacitor C; and frequency of input wave-form? (e) Measure the current and voltage waveform across the rectifier diode. (f) Estimate the average and ms currents through the rectifier diode, Calculate the diode power dissipation. (g) What should be the peak current rating of the diode? (h) Change the initial charge voltage on the capacitor Cr. What is the effect on the input surge current? (i) Change the phase angle of the input V, at start up. Observe the effect on current i. What happens and why? 1) Under whaf conditions do you get maimum peak current to flow through the diodes? (k) Measure the input voltage and current and estimate the power factor. (1) What is the effect of change in Cr value on the input current and power factor? (m) Choose a suitable value for R and construct a simulation model in LTspice and verify your analytic results.
Expert Solution
steps

Step by step

Solved in 2 steps with 2 images

Blurred answer
Knowledge Booster
Three Phase Controlled and Uncontrolled Rectifiers
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,