An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm², and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (µ, = 800 for iron).

An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm², and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (µ, = 800 for iron).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron).
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
show thatvthis is a magnetic flux density: then prove and interpret it with reasons on each step
A magnetic circuit has a length of 100 cm and cross-sectional area of 5 square cm. The total flux is 10 x 10 webers. The coil has 100 turns and current of 4 amperes. What is the magnetic strength? a. 500 AT/m b. 400 AT/m c. 350 AT/m d. 450 AT/m
In a certain cast-steel core series magnetic circuit with a 400 turns, 170 At/m, mean length of 0.16 m and 0. 002 square meters cross-sectional area. the value of current to develop a 0.0004 Wb is
A toroidal core with a mean circumference of 100 cm and a cross-sectional area of 10 cm2 is wound with 500 turns of wire. What current would be required to generate a flux of 1 mWb in the core. Assume the core has a relative permeability of 800
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. -10 cm- - 20 cm- 15 cm 400 turns 15 cm 15 cm Core depth 5 cm
For the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic permeability is 200. its average length is 10 cm -The diameter of the cross-sectional area is 1 cm. Find the current that must pass through the winding to produce 0.5 mWb of flux in a 1mm air-gap magnetic circuit?
A magnetic circuit with a cross-sectional area of 20 cm? is to be operated at 50 Hz from a 120 V rms supply. The number of turns required to achieve a peak magnetic flux density of 1.8 T in the core is
1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
The length of a magnetic circuit in a moving iron instrument is 300mm. The coil around the soft iron core has 360 turns and takes a current of 1.75 A. The core is square in section with sides of 20mm. Take the relative permeability of soft iron as 1100. Determine the total flux