An industrial device with a weight sensitive to the weight of one ton is transported by a heavy vehicle. The device is mounted on a special base that when moving the vehicle, vibrates with a range of 5 cm with an angular frequency of 220rad / sec.Withstands about the stiffness of the desired base so that 80% of the vibration transmitted to the device guide TR = 0.2 %3D

An industrial device with a weight sensitive to the weight of one ton is transported by a heavy vehicle. The device is mounted on a special base that when moving the vehicle, vibrates with a range of 5 cm with an angular frequency of 220rad / sec.Withstands about the stiffness of the desired base so that 80% of the vibration transmitted to the device guide TR = 0.2 %3D

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter15: Experimental Methods

Section: Chapter Questions

Problem 15ETSQ

See similar textbooks

Similar questions

98% ?. l3Ī 7 I 16:58 Month 1.pdf Q1:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three forces. Two forces are known in magnitude and direction and shown in the Figure (150 N and 60 N). The third force is passing through the center of the semi-circle (point C). The resultant of all these forces is a single couple (750 N.m) counterclockwise. a) Determine the magnitude and direction of the third force. b) Determine the magnitude of moment (M). Replace the couple (M) by two vertical equal forces acting at D and E. d) Replace the force (150 N) by and single force at D and a couple. Radius = 5 m 150 N E В M 60 N 4 A F. Q2:- Determine all forces acting on member DEF of the frame shown in Figure below:- 150 Ib/ft F3.0 m -3.0 m
A C-channel has a dimensions of as shown in mm, with a thickness of 75mm. Determine the moment of inertia about x-axis, if the x-axis is also the neutral axis.
VALUE OF THE MAXIMUM DEFLECTION
A cantilever beam of span /carries a uniform distributed load of intensity w throughout its span. Which of the following gives the maximum deflection in the beam? Select the correct response: 5wi4/8EI wi4/2EI wi4/8EI w /2EI
Single choice question: 7. About the vibration period of the structure, which of the following is the correct? （A）The self-vibration period of the structure is inherent in the structure itself and is independent of the seismic intensity.（B）The self-vibration period of the structure is related to the stiffness and mass of the structure itself, regardless of the damping of the structure.（C）The self-vibration period of the structure is not only related to structural quality, stiffness and damping, but also to seismic intensity and seismic duration.（D） The self-vibration period of the structure is only related to the stiffness of the structure, and is independent of mass and damping
Use any meth od: Person A is being chased by person B. Trying to escape, person A walks on a 7m cantilever beam with out kn owing that a bomb is situ ated below the free end of the said beam. The bomb trigger and the bottom of the beam make a gap of 100mm. Assuming Person A weighs 50kg and the beam has an El= 170,000 Nm? (3-a) Determine the rotation of the beam at free endif person A is at 2.4m from the fix support. (3-b) How far can person A go starting from the fix support before the bomb will explode?
A bullet of mass m=0.1 kg is fired with a velocity v0=500 m/s forming an angle θ=30° with the horizontal and gets lodged in a wooden block of mass M=10 kg. The block can roll without friction on a hard floor and is prevented by springs from hitting the wall. Calculate theamplitude and period of vibration of the block and embedded projectile. Each one of the three springs has a stiffness k=3 kN∕m.
Determine the failure mode and plastic moment that might be occurred in the beam. 100KN 30kN/m A 8m 5m 5m C
The beam AB supports a load which varies an intensity of 220 N/m to 890 N/m. Calculate the magnitude and position of the resultant load.
The sinusoidal waveform of an ac circuit shows that the: <-90% O the current is leading the applied voltage by 90 O applied voltage is leading the current by 90 O applied voltage is lagging the current by 90 applied voltage is in phase with the current
3G 48% 2:06 IMG-202103... s Determina the deflection at the fre end uring Hhe compiugate beam below 42
solve very very fast in 15 min please