An autotransformer having a transformation ratio of 0.5 supplies a load of 5 kW. The power transformed from primary to secondary is.......W. An autotransformer having a transformation ratio of 0.49 supplies a load of 5 kW. The power transferred conductively from primary to secondary is.......kW. Used two decimal places for final answer if

An autotransformer having a transformation ratio of 0.5 supplies a load of 5 kW. The power transformed from primary to secondary is.......W. An autotransformer having a transformation ratio of 0.49 supplies a load of 5 kW. The power transferred conductively from primary to secondary is.......kW. Used two decimal places for final answer if

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Similar questions

In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
A 25 kVA, 2 kV(rms)/100 V(rms) single phase transformer is connected between a 120 V(rms) utility supply and a resistive load. The load current was measured to be 20 A(rms). i. Determine the active power of the load. ii. Determine the primary RMS current. iii. Determine the equivalent resistance of the transformer as seen by the utility supply.
67. A 2200/200 V, 60-Hz, transformer takes 0.5 A at a power factor of 0.3 on open circuit when supplied at 200 V. Find the magnetizing current. A. 0.15 A B. 0.345 A C. 0.25 A D. 0.477 A
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Answer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohm
1.List the three steps of nuclear fuel fabrication processes. Also sketch a schematic diagram and label the processes on the diagram. 2 What is geothermal energy? With the aid of a schematic diagram, describe how we can generate electricity using a geothermal energy-driven dry steam power plant. 3.Discuss the differences between Pelton, Francis, and Kaplan turbines.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
Q6. Specification/Range of Power Supply: Q7. What are the types of Loads are available in the Lab? Q8. Write the types of Transformer and the Specification? English unived states ch
AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with 20 coils. What is the exiting voltage and current? a.) 1000v/0.1amp b.) 0.1v/1000amp c.)1000v/1amp d.) 2v/20amp e.) No change
10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and the number of turns of the low voltage winding is N2=34. The high voltage winding is energized with V1= 10 kV rms line-to-line and V2= 400 V rms line-to-line has been taken from the low voltage winding. What is the connection of the low voltage winding if the high voltage winding is Y-connected? Εισαγάγετε την απάντησή σας
Some power devices have bidirectional current capability Select one: O a. True b. False The voltage regulation of the transformer will depend on the load Select one: O a. For mainly inductive or resistive load, the voltage regulation is negative O b. For mainly capacitive, inductive or resistive load, the regulation is positive Oc. For mainly capacitive load, voltage regulation is positive and other loads it is negative. O d. For mainly capacitive load, voltage regulation is negative.
a) The transformer has a turns ratio of 9.45, what is the dc load voltage without considering the ripple voltage?b) The transformer has a turns ratio of 9.45, what is the peak-to-peak ripple voltage? c) The transformer has a turns ratio of 9.45, what is the dc load voltage considering the ripple voltage? Answer in 2 decimal places.