An angle with staggered fasteners in each leg is shown in Figure. A36 steel is used, and holes are for 22mm-diameter bolts. The thickness of the angle bar is 12mm. Ag = 4,390 mm2. All measurements are in mm. Assume the hole diameter is 2mm larger than the bolt diameter. 60 65 25 75 75 50 4@40mm HITTI O O 1. Determine the design strength for net area for LRFD.

An angle with staggered fasteners in each leg is shown in Figure. A36 steel is used, and holes are for 22mm-diameter bolts. The thickness of the angle bar is 12mm. Ag = 4,390 mm2. All measurements are in mm. Assume the hole diameter is 2mm larger than the bolt diameter. 60 65 25 75 75 50 4@40mm HITTI O O 1. Determine the design strength for net area for LRFD.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.4.3P

See similar textbooks

Similar questions

A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 215 x 3 x %6 LLBB Determine the design tensile strength for LRFD. Select one: а. 66 b. 156 c. 78 d. 132
Design the size and length of Fillet weld for the lap joint shown below, Use SMAW E70XX process, plates are A-36 steel? 90k LL 40k DL R-X7 5" Gusset P 8 90k LL 40k DL
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An.a) Determine the allowable tensile strength for ASD.b) Determine the design tensile strength for LRFD.
Find the available strength of the S-shape shown in the figure. The holes are for 3/4-inch- diameter bolts. Use A36 steel. Use LRFD Use ASD (1 (2) 3½" I S15 × 50 $23/4" CIVIL ENGINEERING- STEEL DESIGN 1½" 12" e b С d Answer VUZMGL
Problem 01 The lap joint in the figure is fastened by four 20 mm Ø A325X bolts. Calculate the maximum safe load P that can be applied if the plates are 25 mm thick A-36 steel Use ASD. P 4 @ 40 mm 2@ 60 mm Problem 02 Based on the bolt capacity, determine the required number of 20 mm Ø A490F bolts needed to develop the full strength of the steel plate in Problem 01 if P = 250 kN. Assume that the surface is Class A and the hole size is standard. Use LRFD
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
Prepare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area Stress and d) allowable stress. Applied force range – 500 to 1000 N (in step of 100 N) Bolt diameter range – 10 to 25 mm (in step of 5 mm) Plate thickness – 10 mm Consider ultimate tensile strength as 460 N/mm2. And consider factor of safety as 1.5.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt hole = 22 mm. %3D 50, 100 100 99.45 50.55 100 Properties of 150 mm x 100 mm x 12.5 mm angle A - 3065 mm- y - 50.55 mm Fy - 248 MPa Fu 400 MPa Determine the design strength due to yielding in the gross section. (kN)