• An aluminum pot contains water that is kept steadily boiling (100 °C). The bottom surface of the pot, which is 12 mm thick and 1.5x10* mm2 in area, is maintained at a temperature of 102°C by an electric heating unit. Find the rate at which heat is transferred through the bottom surface. Compare this with a copper based pot. Tc 000 L=12mm Base of pot TH A= area of base

• An aluminum pot contains water that is kept steadily boiling (100 °C). The bottom surface of the pot, which is 12 mm thick and 1.5x10* mm2 in area, is maintained at a temperature of 102°C by an electric heating unit. Find the rate at which heat is transferred through the bottom surface. Compare this with a copper based pot. Tc 000 L=12mm Base of pot TH A= area of base

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.1P

See similar textbooks

Similar questions

Two containers are alike except that the flat base of one is brass, and the other is silver. Water in these containers is boiling away at 100.0 degrees Celcius at the same rate. The temperature of the heating component on which the brass base is sitting is 175.0 degrees Celcius. Assume that heat enters the water only through the bases of the containers and find the temperature of the heating component on which the silver bottom rests.
Water is to be boiled at atmospheric pressure in a polished copper pan placed on top of a heating unit. The diameter of the bottom of the pan is 00.2 m. If during 30 minutes the water level is dropped by 0.1 m, calculate the inner surface of the bottom of the pan. Assumptions 1 Steady operating conditions exist. 2 Heat losses from the heater and the pan are negligible 3 The boiling regime is nucleate boiling. Note. Write your answer step by step and clearly explain your work. You need to upload a file.
A tank of water is kept boiling with an internal 10 kW heater, and loses energy through evaporation and through the walls of the tank. temperature of 20 °C. The surrounding environment has a a) Calculate the heat loss through the walls, which are made of 5 mm thick stainless steel with a total surface area of 2.8 m². Calculate the percentage of resistance to heat transfer contributed by the boiling water, the walls and the air. Assume natural convection of the air. Which is the controlling resistance? b) Calculate the rate of evaporation of water. Data: Thermal conductivity of stainless steel Latent heat of vaporisation of water = 2257 kJ/kg Take the convective heat transfer coefficient for boiling water to be about 45000 W/m² K, ana for air under free convection to be 35 W/m K. 19 W/m K
AS& Heat Transfer in Steam Heater Water at an average of 70°F is fiowing in a 2-in. steel pipe, schedule 40. Steam at 220°F is condensing on the outside of the pipe. The con vective coefficient for the water inside the pipe is A = 500 btu/h ft2.°F and the con- densing steam cocfficient on the outside is h = 1500 (a) Calculate the heat loss per unit length of1 ft of pipe using resistances. (b) Repcat, using the overall based on the inside area Ap (c) Repeat, using U 13.2- Ans. (a)q= 26 710 btu/h (7.828 kW). (b) Uj = 329.1 btu/h-ft2."F (1869 W/m2. K), (c) U.= 286.4 btu/h ft2.°F (1626 W/m2. K)
A 15 lb. block of brass with a specific heat of 0.089 is heated to 189°C and the immersed in 5 gal. of water at 66°C. What is the final temperature of the brass and water? Assume there is no heat loss.
What are the surface condensing systems? Explain their working.
Estimate the power required to boil the water in a copper pan (Cs,f = 0.013 and n = 1), 180 mm in diameter. The bottom of the pan is maintained at 115 ℃ by the heating element of an electric range. Properties of Water (1 atm): Tsat = 100℃, ρl = 957.9 kg/m3, ρv = 0.5955 kg/m3, Cpl = 4217 J/kg.K, μl = 279*10^-6 N.s/m2, Prl = 1.76, hfg = 2257 kJ/kg, σ = 58.9*10^-3 N/m. Select one: a. 16420 W b. 18166 W c. 16240 W d. 11760 W
It has been found that condensation forms on the outside of the refrigerator when the temperature on the surface is T1 and lower certain parts during the year. If the temperature on the inside of the refrigerator is T2 , how thick insulation needed to avoid condensation? The cooling effect in the refrigerator is ?. The refrigerator wall is built (from the outside) with 1 mm metal (thermal conductivity is k1),mineral wool (thermal conductivity is k2)and an additional layer of 1 mm metal. T1 (°C)= 15 , T2(°C)=3 , ? (W)=70 , k1 (W/m·K)=15 , k2 (W/m·K)=0.04
*14. ao Two pots are identical except that the flat bottom of one is alu- minum, whereas that of the other is copper. Water in these pots is boiling away at 100.0 °C at the same rate. The temperature of the heating element on which the aluminum bottom is sitting is 155.0 °C. Assume that heat enters the water only through the bottoms of the pots and find the temper- ature of the heating element on which the copper bottom rests.
Draw( insert image) the parts of the Industrial Water Tube Boiler. And discuss the function of each part.
Bourdon tube is also referred to as an
Discuss the concept of real-time thermal monityoring system.