An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 50 mm and inner diameter of 40 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr = 60 MPa (concrete). 100 kN 500 mm

An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 50 mm and inner diameter of 40 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr = 60 MPa (concrete). 100 kN 500 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.9P: A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d...

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A cylinder filled with oil is under pressure from a piston, as shown in the figure. The diameter d of the piston is 1,80 in. and the compressive force F is 3500 lb. The maximum allowable shear stress t^^, in the wall of the cylinder is 5500 psi. What is the minimum permissible thickness t„± of the cylinder wall? (Sec figure
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial direction
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
Five bars, each having a diameter of 10 mm. support a load P as shown in the figure. Determine the plastic load Ppif the material is clastoplastic with yield stress
A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mmhas been designed to withstand a maximum internal pressure of 200 MPa inservice. During operation, the pressure within the cylinder is retained by a freelysliding piston. The steel used in the manufacture has Young’s modulus of 210GNm-2.Note: There is no axial stress generated in the cylinder wall in this application.1. Elastic Stress Distributions in a Single Cylindera) At an operating pressure of 200 MPa, calculate using Lame’s equations theradial and circumferential stresses at the cylinder bore and the outersurface.Graphically present (sketch) the general form of variation of each of thesestresses across the cylinder wall, clearly indicating the calculated values atthe cylinder bore and at the outer surface. b) For the same operating pressure, calculate the maximum shear stressvalues at the cylinder bore and the outer surface.Hint: For axisymmetric problems, there are no shear stresses generated onthe…
A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force maximum allowable P that can be applied to the column if the allowable stresses are 12 kpsi in steel and 1200 psi in concrete. Esteel = 29 Mpsi, Econcrete = 3.6 Mpsi. Answer A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force maximum allowable P that can be applied to the column if the allowable stresses are 12 kpsi in steel and 1200 psi in concrete. Esteel = 29 Mpsi, Econcrete = 3.6 Mpsi. Answer: 560 kips.
A rubber ball is inflated to a pressure of 60KPa. At that pressure, the diameter of the ball is 230mm and the wall thickness is 1.2mm. The rubber has a modulus of elasticity of E = 3.5MPa and Poisson’s ratio of 0.45. (a)Compute the maximum tensile stress. (b)If the allowable tensile stress of the rubber ball wall is 2.5MPa, compute the internal pressure the rubber ball could be inflated.
Please help me understand this solution. I want to know how the stress in concrete was solved for. I don't quite understand beyond part ii). Attached is the problem and the solution This is the problem: The figure shows the cross section of a circular steel tube that is filled with concrete and topped with a rigid cap. Calculate the stresses in the steel and in the concrete caused by the 200-kip axial load. Use Est = 29 x 106 psi and Eco = 3.5 x 106 psi.