An aluminum column (0,= 200 MPa) has a length of 8 m. and is fixed at the top and pinned at the bottom. The column is braced in the weak direction at a point located 5 m from the bottom of the column. If the cross-sectional area has the dimensions shown and the factor of safety is 2.5, determine the maximum load that can be safely applied to the column. 310 mm 10 mm 10 mm 180 mm 10 mm

An aluminum column (0,= 200 MPa) has a length of 8 m. and is fixed at the top and pinned at the bottom. The column is braced in the weak direction at a point located 5 m from the bottom of the column. If the cross-sectional area has the dimensions shown and the factor of safety is 2.5, determine the maximum load that can be safely applied to the column. 310 mm 10 mm 10 mm 180 mm 10 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A column consists of a 2.5 m long hollow tube with an outside diameter equal to 1.5 times that of the inside diameter. The column must carry an axial load of 40 KN without buckling. Use a factor of safety of 5 and calculate the dimensions of the tube if one end is fixed and the other end is free. Use the Euler formula and take ?=200 ???.
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. Ilonger than the tube of length L = 10.52 in. Find the maximum safe load P (in Ib with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.64 sq, in. area of aluminum = 3.04 sq, in. E of copper = 17022171 ksi E of aluminum = 10073078 ksi allowable stress for copper = 19926 ksi allowable stress for aluminum = 10407 ksi Bearing plate 0.005 in. Copper - Aluminum
A cylindrical pressure vessel has an internal diameter of 1600 mm and is subject to an internal fluid pressure of 30 bar. The plate is 15 mm thick with an ultimate tensile stress of 600 N/mm2. The efficiencies of the circumferential and longitudinal joints are 50 and 80 percent respectively. Determine the factor of safety.
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
A pivot-ended solid steel bar having a diameter of 50 mm and a length of 2.0 m will be used to support a compressive load. A factor of safety of 3.0 is specified and the eccentricity ratio ec/r² = 0.50. Determine (a) The maximum safe compressive load (b) The implied value of eccentricity Oy = 300 MPa, E=200 GPa
Q#3. An aluminium strut 16 ft long has a rectangular cross section 2 in by 3.5 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3.5 in dimension; and as fixed column about an axis perpendicular to 2 in dimension. Determine the safe central load with a factor of safety of 2 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it.
What is the maximum force P that can be applied to the handle so that the steel control rod AB does not buckle? The rod has a diameter of 0.25 m. It is pin connected at its ends. E =76 MPa. Select 3m 2m one: 10.65 A kN O 8.49 kN 5 m 5.05 kN O 3.84 kN O 14.03 kN
The piston rod of an air operated press has a length of 2500 mm, with its right-hand end pin connected to the operating lever and the piston end of the rod fix ended. The rod is made of a material whose Sy = 250 MPa and E = 200 GPa. For a factor of safety of 3.5, determine the maximum safe compressive load of the rod in Newtons if its diameter is 47.5 mm. Round your answer to 4 significant figures.
5. A toggle device is used to compact scrap steel as shown below. If a Safety Factor of 3.5 is desired, and all the connections are pinned, design the 2 links of the toggle to have a circular cross-section and to be made from steel with Sy = 151 ksi and E = 30000 ksi. The force required to crush the shavings is 5000 lb. -Shavings Crushing force = 5000 lb 60 in- 15° 12 Toggle links- Applied force 60 in D = ? Section A-A Length typical both links
4) A steel column is braced at the midpoint, C, as shown below. The brace only acts in the x-y plane. The column dimensions are L=15 in, a=0.25 in, and b=1 in. The material properties are Sy=36ksi, and E=30 x 106 psi. What is the critical force, P, for a factor of safety of SF=3? B L/2 14: L/2 y
Q1: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN, determine (a) the load carried by the steel rod and the brass bush; (b) the compressive stress set up in each material. The modulus of elasticity for steel, E. = 210 GN/m², and brass, E = 100 GN/m².
8. A concrete wall footing with a width of 0.9 m and a depth of 0.6 m supports a centrally placed 0.6-m-thick wall. The ultimate bearing stress for the soil under the footing is 47 kN/m2. What is the height of the wall if a factor of safety of 5.0 is used? Concrete weighs 23.5 kN/m3 (assume depth of one meter) NOTE: please check options 0.6m R(m) Jestion 0.6m tely ar ate 05.16 m oogle pject) O 14.4 m MG-40 16 O5 pm ourse 1.8 m