After pressure spraying, there is a thin layer of water (at 70°F) left inside of a 24 nch diameter retort that is 20 ft. long. A jet heater is place in front of the entrance to the tube. The jet heater is turned on and produces 2000 ft³/minute of 120°F air. What is the mass transfer convection coefficient of the water into the ir?

After pressure spraying, there is a thin layer of water (at 70°F) left inside of a 24 nch diameter retort that is 20 ft. long. A jet heater is place in front of the entrance to the tube. The jet heater is turned on and produces 2000 ft³/minute of 120°F air. What is the mass transfer convection coefficient of the water into the ir?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.29P

See similar textbooks

Similar questions

An evaporator is concentrating F kg/hr at 311K of a 20 wt % solution of NaOH to 50%. The saturated steam used for heating is at 399.3 K. The pressure in the vapor space of the evaporator is 13.3 kPa abs. The overall coefficient is 1420 W/. K and the area is 86.4 square meters. Calculate the feed rate F of the evaporator.
QUESTION 1 temperature of 200°C from feed water of 5°C. The steam has a dryness fraction of 0,9 when leaving the evaporator. The boiler uses coal with a calorific value of 31MJ/ka and the steam leaves the plant at a rate of 8kg per kg fuel burnt. Determine: 1.1.1 the boiler efficiency; THER MOTTADE ETA 1.1.2 the equivalent evaporation from and at 100°C;
Steam at a pressure of 28kpa is passed into condenser and it leaves as condensate at a temperature of 592 0 Cooling water circulates through the condenser at the rate 9 of 45 kg/min. It enters at 152 and leaves at 30°C.It the Steam flow rate is 1.25 kg/min, determine the dryness r fraction of Steam as it enters the condenser.
A spray condenser is to be used to condense steam at a pressure of 0.105 bar (Tat using water at 27° C. The injection velocity of the drops is 6 m/s and their mean diameter is 2 mm. How long must the condenser vessel be to achieve 95% utilization of the cooling water? (Use vapor properties at 320 K and liquid properties at 310 K.) 320 K)
An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps against a condensing temperature of 40°C. For the two different evaporating temperatures of -10 °C, compute the refrigerant flow rate in kg/s assuming that the clearance volumetric efficiency applies.
Air at a dry ball temperature of 9m5 ° and rh 4% is passed over the cooling coil so that the temperature of the dry ball of air becomes 50 ° C. How much heat is released from the air in the process
100 C² saturated steam enters the turbine Vapour at 6 MPa and Sahared liquidenters the pump at apressure of 0.01 MPa If the Detemain as heat rate to borler is ISO MU D thermal off
if 2460 kj/kg of heat is added to water at 0 degrees celcius to produce wet steam at 1500 kpa , calculate th dryness fraction .
A Copper ball at 40'Cis dropped in a mug containing water at 40°C. The heat will Select one: O a.not flow from Copper ball to water or from water to Copper ball O b. flow from Copper ball to water O c. Increase the temiperature of both O d. flow from water to Copper ball
A four-effect evaporator is being considered for concentratinga fruit juice that has no appreciable boiling-point elevation.Steam is available at 143.27 kPa, and the boiling point of the product in the fourth effect is 45°C. The overall heat-transfer coeffi cients are 3000 W/(m 2 °C) in the fi rst effect, 2500W/(m2 °C) in the second effect, 2100W/(m2°C) in thethird effect, and 1800W/(m2°C) in the fourth effect. Calculatethe boiling-point temperatures of the product in the fi rst,second, and third effects. Assume the heating areas in all theeffects are equal to 50m2 each. The mass fl ow rate of steam tothe fi rst effect is 2400kg/h, the feed rate to the fi rst effect of 5%total solids fl uid is 15,000kg/h, the concentrated product fromthe fi rst effect leaves at 6.25% total solids, and the concentrationof product leaving the second effect is 8.82% total solids. Make it in the form of an example solution spreadsheet .....
A single-effect evaporator is being used to concentrate10,000 kg/h of tomato juice from 5% total solids to 30% totalsolids. The juice enters the evaporator at 15°C. The evaporatoris operated with steam (80% quality) at 143.27 kPa. Thevacuum inside the evaporator allows the juice to boil at 75°C.Calculate (a) the steam requirements and (b) steam economyfor the process. Assume the condensate is discharged at 75°C.The specifi c heat of the liquid feed is 4.1 kJ/(kg°C) and theconcentrated product is 3.1 kJ/(kg°C). Make it in the form of an example solution spreadsheet .....
Elaborate and explain the piping equipments in cryogenic plant including the pipes and fittings, valves, filters, pressure regulators, expansion joints, strainers.