A workshop crane is lifting a load of 28 kN through a wire rope and a hook. The weight of the hook etc is 15 kN. The rope drum diameter may be taken as 30 times the diameter of the rope. The load is to be lifted with an acceleration of 1.2 m/sec2. Take a factor of safety of 6 and Young's modulus for the wire rope is 80 kN/mm2. The ultimate stress may be taken as 1800 MPa. The cross-sectional area of the rope may be taken as 0.38 times the square of the wire rope diameter. Neglect the effect of impact load. Calculate the diameter of the wire гope.

A workshop crane is lifting a load of 28 kN through a wire rope and a hook. The weight of the hook etc is 15 kN. The rope drum diameter may be taken as 30 times the diameter of the rope. The load is to be lifted with an acceleration of 1.2 m/sec2. Take a factor of safety of 6 and Young's modulus for the wire rope is 80 kN/mm2. The ultimate stress may be taken as 1800 MPa. The cross-sectional area of the rope may be taken as 0.38 times the square of the wire rope diameter. Neglect the effect of impact load. Calculate the diameter of the wire гope.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Similar questions

A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
Find the tension of the cord that extends from point C to D and compute for stress experienced by the cable if it's diameter in 1.51 in2. Neglect the members weight and friction. Round-off your answer into the nearest whole number. 150 Ivft B 6ft 6 ft E -12 ft 8 ft ANS: T = Ib, Stress = ksi
Find the tension of the cord that extends from point C to D and compute for stress experienced by the catble if it's diameter in 1.51 in? Neglect the members weight and friction Round-off your answer into the nearest whole number 150 Ib/ft 6 ft 8 ft 6 fh -12 ft
An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). The center of gravity of the arm is 1.2 m from theaxis of the pole. A wind force of 300 N also acts in the (-y)direction at 9 m above the base. The outside diameter ofthe pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressivestresses σt and σc, respectively, in the pole (at its base)due to the weights and the wind force.
The thick walled cylinder of a hydraulic system is acted by a hydraulic pressure of 370 psi while themaximum load of the piston is 5500 lbs. If the allowable tensile stress is 2 ksi, find the required wallthickness of the cylinder.
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Find the longitudinal stress in the tank.
In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a stress equivalent to your SN and MN in kips respectively, determine the maximum weight of that body. Neglect the weight of wood and cable. Note: Round off your answer in two decimal places. ... Cable (A = 0.5 in 2) 9 ft C B 12 ft Weight A Wood Strut ( A 16 in 2)
Find the stresses in each direction, also find the change in volume of the block of dimension 120 mm x 60 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (tensile), 13 kN (compressive) respectively, Take E as 180 GPa, Poisson's ratio as 0.3. The stress along length direction (Unit in kN/m2)= _____________ The stress along width direction (Unit in kN/m2)= _____________ The compressive stress along depth direction (Unit in kN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of ø = 64.0 ° with the floor and rope segment CD creates an angle 0 with the horizontal. If both ropes BCA and CD can support a maximum tensile force Tmaz = 165 lb. what is the maximum weight Wmar of the crate that the system can support? What is the angle e required for equilibrium? Express your answers numerically in pounds and degrees to three significant figures separated by a comma. • View Available Hint(s) nν ΑΣφ vec Wmax.0 = lb, degrees
Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 55 mm x 40 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 14 kN (tensile), 20 kN (compressive), 10 kN (compressive) respectively. Take E as 160 GPa, Poisson's ratio as 0.3 (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) The stress along length direction (Unit in MN/m?)=. The compressive stress along width direction (Unit in MN/m2)=. The compressive stress along depth direction (Unit in MN/m2)=. The change in volume of the block is (unit in mm3) =.
Find stress and of each segment and find displacement of each segment
Calculate the minimum diameter for a cylindrical vessel that is to carry a gas at a pressure of 10 MPa. The thickness of the vessel is 38 mm and the hoop stress is 83 MPa and the longitudinal stress is 40 MPa. 1 Add file