A truck is attempting to pull a 500Ñ weight crate that is originally at rest to the entrance of the factory as shown in Figure Q2 (a). The coefficient of static friction is 0.4 and the coefficient of kinetic friction is 0.3. (i) Determine the tension of the cable when the truck is just about to start to move. (ii) Determine the acceleration of the truck if the tension in the cable is 350N. 30

A truck is attempting to pull a 500Ñ weight crate that is originally at rest to the entrance of the factory as shown in Figure Q2 (a). The coefficient of static friction is 0.4 and the coefficient of kinetic friction is 0.3. (i) Determine the tension of the cable when the truck is just about to start to move. (ii) Determine the acceleration of the truck if the tension in the cable is 350N. 30

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.3P: Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair...

See similar textbooks

Similar questions

The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
Task 2 (a) The sports car, having a mass of 1900 kg, travels horizontally along a 20° banked track which is circular and has a radius of p= 100 m. If the coefficient of static friction between the tires and the road is 4, = 0.2, determine the maximum constant speed at which the car can travel without sliding up the slope. Neglect the size of the car. (b) Find all the forces on the car of part (a). (c) If the car is treated as a rigid body, draw the free-body-diagram. Task 3 Provide a practical application of three interconnected rigid bodies such that two of them rotate about a fixed axis and the third one has translational motion. Assume the dimensions of the three bodies, and speeds and accelerations of the two rotating rigid bodies. Find the speed and acceleration of translating rigid body.
Q3.) A front wheel drive industrial truck is used to move a solid 1500 kg cylinder with a diameter of 1 meter up the 30° incline. The coefficients of static and kinetic friction between the cylinder and both surfaces are 0.4 and 0.2, respectively. Determine the required tractive force between the truck's front tires and the horizontal surface necessary to begin moving the cylinder up the incline. Assume negligible friction between the rear wheels and the horizontal surface. Consider two possible ways the cylinder might move up the incline. Note: the tractive force represents the friction force between the front wheels and the horizontal surface directed to the right. 30°
3) A truck is moving down a 10° incline. The driver strongly applies the brakes to avoid a collision and the truck decelerates at the steady rate of 1 m/s². If the static coefficient of friction u between the load W and the truck is 0.3, will the load slide or remain stationary relative to the truck trailer? The weight of Wis 4500 N and is not held to the truck by cables. n W
1. A force of 69N is needed to start an 6.9kg box moving across a horizontal surface. Calculate the coefficient of static friction. If the box continues to move with an acceleration of 1.69 m/s2. What is the coefficient of kinetic friction? 2. A box of 45ON is lying in an inclined plane with angle of 35 degrees. If the applied load to move the box is 269N. Determine the net Ff and the acceleration of the box if the coefficient of static friction is 0.35 and the coefficient of kinetic friction is 0.28.
Q1. m-1 kg m,=4 kg The mechanism set up with m,, m, and weightless pulleys is as shown in the figure. Then, the masses are released. Static and kinetic friction between the inclined plane and m, are 0.6 and 0.5 respectively. What are the accelerations of m, and m,? (g = 10 m / s². Frictions and mass of the pulley are ignored.) Q2. 300 m/s .*........ yatay 100 m/s 320 m x=? A plane is flying horizontally at an altitude of 320 m with 300 m/s speed. It launches its bomb with 100 m/s speed relative to the plane as shown. How many meters away from the castle should the plane launch its bomb to hit the castle. (g=10 m/s², sin370=0.6; cos37°=0.8) Q3. 2 kg The object in the frictionless cone in the figure is making a uniform circular motion. Calculate, a) the normal force that the cone exerts on the object, b) centripetal force applied to the body, c) Find the speed of the object.
For the system shown, the masses of A and B are 55kg and 135kg, respectively. the coefficient of static friction between block B and surface C is 0.12 and the coefficient of static friction between blocks A and B is 0.10. the coefficient of friction between the rope and the pulley is 0.10. What is the tension force in the rope connected to block B if the system is in equillibrium? What is the magnitude of the friction force between block B and the horizontal surface C if the system is in equillibrium? What is the maximum mass that can be suspended as shown and still maintain equillibrium.
Block A is sliding down and pulling up both Block B and Block C. Find the accelerations of each body and the tension of rope if the coefficient of friction at Block A is 0.25 and at Block C is 0.35 A= 2000b B= 500 b C: 1000lb 314 A
A2.3-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle e is 40°, the angular velocity of the arm about a horizontal axis through O is 54 deg/s clockwise and its angular acceleration is 209 deg/s? counterclockwise. In addition, the hydraulic element is being shortened at the constant rate of 480 mm/s. Determine the necessary minimum gripping force Pif the coefficient of static friction between the sphere and the gripping surfaces is 0.44. Compare Pwith the minimum gripping force P; required to hold the sphere in static equilibrium in the 40° position. 0.9 m Answers: P= N Ps=