A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.

A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
For the phasor diagram in figure 6 express the voltages in sinusoids for a period of 5ms. Im Re )e,=45° e,=20 Vz=10 V2=8 Figure 7 a. Va(t)=. b. V2(t)=. c. What is the rms voltage of V1 = d. What is the rms voltage of V2=_ e. What is the frequency in Hz = f. What is the angular frequency =. In terms of lagging and leading what is the exact phase relationship between V, (t) and V2(t) g.
How to solve for a (+) Phase Sequence and (-) Phase Sequence? Give an example and explain the steps.
What is the average power in ghe single phase ac circuit with the purely resistive load? It is sinusoidal steady state excitation.
Two alternating voltages are represented by vị = 50 sin wt volts and v2 = 100 sin(wt - -). Draw the phasor diagram and find by calculations a sinusoidal expression to represent vi and v,. www The instantane ous values of two alternating currents are given by i = 20 sin wt and i, = 10 sin (wt + ) A. Find the sinusoidal expression for (i1 + i2) by drawing phasors and by calculations.
Please explain in detail. A. In a series circuit, if the AC voltage is measured across the AC voltage source, will there be any variations in the phase of the AC voltage across each resistor from the measured AC voltage across the source? B. In an AC voltage source, why does voltage vary with time? Please explain in detail. C. In a series circuit, are the frequencies of the AC voltages across each resistor the same? Why is this so? ...
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
about Three-phase Circuits
C. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
detalls by Q-2: Explain the phase difference between voltage and current for a sinusoidal source voltage V(t)= Vo sin(wt) when it is applied in a circuit to a) On a resistor, b) on a solenoid, c) on a capacitor. Draw a separate figure for each case for voltage and current.
AC Circuits Current, Voltage, Power, Power Factor and Phasor Diagrams. Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage source. (ii) Find the total current IT supplied by the source. (iii) Sketch phasor diagram of Vs and IT and State whether IT leads or lags Vs (iv) Determine the power factor angle for the circuit. 9. L R1 1002 0.213H IT Vs R3 1502 C 12020°V 22µF 60HZ R2 50Ω Figure 3 Answers |(1) Zr = (ii) IT= (iii)