(a)The gain of a bandpass filter at its lower cutoff frequency is 12. The upper cutoff frequency is11.2 kHz and the Q is 30. Determine:()The gain at the centre frequency(ii)The centre frequency(ii)The bandwidth(b)The input to the filter in (a) has the following components:Vi1: 2V rms at 2 kHz andVi2: SV rms at 20 KH2Determine the rms values of these components in the filter's output.

Note: As per our honor code, we are authorized to answer only one question at the moment. If you…

(a) The gain of a bandpass filter at its lower cutoff frequency is 12. The upper cutoff frequency is 11.2 kHz and the Qis 30. Determine: (0) The gain at the centre frequency (i) The centre frequency (i) The bandwidth (b) The input to the filter in (a) has the following components: Vi1: 2V rms at 2 kHz and Vi2: SV rms at 20 KHz Determine the rms values of these compoinents in the filter's output.

(a) The gain of a bandpass filter at its lower cutoff frequency is 12. The upper cutoff frequency is 11.2 kHz and the Qis 30. Determine: (0) The gain at the centre frequency (i) The centre frequency (i) The bandwidth (b) The input to the filter in (a) has the following components: Vi1: 2V rms at 2 kHz and Vi2: SV rms at 20 KHz Determine the rms values of these compoinents in the filter's output.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?
show step by step with diagrams and formula on how to arrive at the output waveform for a center-tapped full-wave with filter capacitor
filter specification a. What kind of filter is this? b. What is the transition band of the filter is given as ₂ = 0.4, , = 0.5, ₁ = 0.01, &₂ = 0.00001, c. Draw the absolute specification d. What is the specification in relative? e. Draw the relative specification. f. If the filter is applied on a signal sampled at 100 kHz, what are the frequency edges in Hz?
[Q1](A) The gain of a second order band-pass active filter at its upper cutoff frequency is 42 dB. The lower cutoff frequency is 10.8 KHz and Q-factor is 50. Assume that the center frequency fo, which is equal to 15.3 KHZ, is midway between the cutoff frequencies. Determine 1- The gain at center frequency. 2- The upper cutoff frequency. 3- The bandwidth. (B) Design the filter with the specifications given in part (A) with equal values using Bessel approximation technique. Choose C-0.01 nF and draw the complete circuit diagram for the designed filter.
Draw the circuit diagrams of a first and a second order band pass filter and indicate its lower and upper cut off frequencies. Do the same for band stop filter. thanks in advance! ..
show how to arrive at the output waveform for a center-tapped full-wave with filter capacitor
1. Choose which basic filter response suit the signal output criteria in the figure 2. State your reason. 2. Sketch the basic filter response to suit the output citeria in Figure 2. (with labelling of passband, transition region and cut-off frequency). 3. Choose 1 type of filter if a flat pass-band gain response is required.
Q)Design a Discrete Time Low Pass Filter for a signal. Butterworth Filter. Chebeyshev Filter The specifications are:(Voice Signal) 1) Passband Fp=4 kHz, with 0.2 dB ripple; Stopband FS 4.5 kHz, with 45 dB ripple. Sampling Frequency Fs = 22 kHz. (Use For Both Filters). 2) passband ripple = 0.2 stopband ripple-45 passband frequency- 1300 stopband frequency = 1500 sampling frequency = 10000. (Chebeyshev Filter) 3) Passband ripple = 0.5 stopband ripple = 50 passband frequency = 1200 stopband frequency = 2400 Sampling Frequency= 10000. (Butterworth filter)."
Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)
Q)Design a Discrete Time Low Pass Filter for a signal. Butterworth Filter. Chebeyshev Filter The specifications are:(Voice Signal) 1) Passband Fp = 4 kHz, with 0.2 dB ripple; Stopband FS 4.5 kHz, with 45 dB ripple. Sampling Frequency Fs = 22 kHz. (Use For Both Filters). 2) passband ripple - 0.2 stopband ripple 45 passband frequency 1300 stopband frequency = 1500. sampling frequency=10000. (Chebeyshev Filter) 3) Passband ripple=0.5 stopband ripple 50 passband frequency 1200. stopband frequency = 2400 Sampling Frequency= 10000. (Butterworth filter)." 4)Choose your own Specifications
a)Draw a general graph showing its gain verses frequency with gain in dB vs log of frequency and indicate the cut-off Frequency. b) Draw a simple, single resistor, single capacitor high pass filter. What is the formula for the cut-off frequency for this filter? c) Draw a graph of its gain verses frequency and label its cut-off frequency.
Design a single pole low pass filter with a gain of 10 in the passband and a 3dB frequency of 5kHz. The minimum resistance in the passband for this filter is to be of 10k-ohms. What is the value of C in nF and in two decimal places only.?