A tank in the shape of a triangular trough is full of water. To empty the tank, the water is pumped upward through the outflow pipe located on the top of the tank. Compute the work necessary to empty the tank. Write out the integral. Note: The volume density of water is 1000kg/m3. Also, assume that the acceleration due to gravity is 9.8m/s2. 2m 3 m 1 -3m- 8 m

A tank in the shape of a triangular trough is full of water. To empty the tank, the water is pumped upward through the outflow pipe located on the top of the tank. Compute the work necessary to empty the tank. Write out the integral. Note: The volume density of water is 1000kg/m3. Also, assume that the acceleration due to gravity is 9.8m/s2. 2m 3 m 1 -3m- 8 m

Name: Needs Complete typed solution with 100 % accuracy. A tank in the shape
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Needs Complete typed solution with 100 % accuracy. A tank in the shape of a triangular trough is full of water. To empty the tank, the water is pumped upward through theoutflow pipe located on the top of the tank. Compute the work necessary to empty

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to H=7.5 m? D=20 cm H water h d1= 4cm d2=3 cm v1=5 m/s v2=2 m/s
Determine how much work it takes to empty a hemispherical pond with a depth of 5 meters. The outlet for the pump is 1 meter above the surface of the pond. The density of water is 1000 kg/m^2 and gravity is 9.8 m/s^2 a. draw a sketch of the system b. set up the integral C. solve the integral and report your answer.
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
If a pump is capable of lifting 5000kg of water through a vertical height of 60m in 15 min, the power of the pump is
A fluid with specific weight 32 lb -flows through the pipe below as it narrows from a diameter of 4.8 in. to a diameter of 2.9 in. The fluid has an inlet velocity of 0.7 ft/s. ft³ lb A fluid with specific weight 84 is used to measure the pressure in the barometer attached to points A and B. Find the difference in heights of the barometer, h₁ - h₂ Report your result in inches. h₁ ·A D₁ B D₂ h₂
A centrifugal pump is required to handle 50 lit/sec of gasoline against a net pressure of 4 kg/cm'. Determine the head in m of liquid and the HP required by the pump, if its overall efficiency is 62%. Take the specific gravity of gasoline as 0.7. (57 and 43) A centrifugal pump draws water from a sump through a vertical 15 cm pipe. The 3.5 m above water level in the sump. While pumping 35 lit/sec, gauges near the pump at entrance and discharge read 0.35 kg/cm and+1.8 kg/cm respectively. The discharge gauge is 0.5 m above the suction gauge. Determine the horsepower output of the pump. pump has a horizontal discharge pipe 10 cm diameter which is (10.82) To p. edict the performance of a loge centrifugal pump, its model, having the following specification, was made: P = 24 IIP H=8 m N=925 rpm Diameter of model pump impeller is 9 times smaller than that of the prototype. The prototype pump has to work against a head of 30 m. Find its working speed and HP required to drive it. Determine also…
A hemispherical tank of diameter 4 m contains water up to a height of 2.0 m. An orifice of diameter 50 mm is provided at the bottom. Find the time required by water (i) to fall from 2.0 m to 1.0 m (ii) for completely emptying the tank. Take Cd= 0.6
A 60 mm diameter pipe has a discharge of 450 litre/min. At a section the pipe has a sudden expansion to a size of 90 mm diameter. If the pressure just upstream of the expansion is 20 kPa, calculate the pressure just after the expansion. Assume the pipe to be horizontal at the expansion region. :2 d2 2 :2
B-Draw the hydraulic gradient line and energy gradient line for the pipe system shown in figure below. F Reservoir A D Reservoir B
What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to H=7.0 m? D=20 cm – H water d1= 4cm d2=3 cm v2=2 m/s v1=5 m/s
A spherical tank with radius 3 m is half full of a liquid that has a density of 900 kg/m³. The tank has a 1 m spout at the top. Find the work W required to pump the liquid out of the spout. (Use 9.8 m/s² for g.) W = J h
Initially tank I and tank II each contains 100 gal of brine, tank I having 200 lb salt and tank II 50 lb of salt in solution. Brine runs at 2 gal/min from tank I to tank II through one pipe and at 3 gal/min from tank II to I through another pipe. The brine is kept well stirred. How much salt (in lb) will be in the second tank after 50 min?