A swivel bridge is bought into the desired position by means of a double–acting cylinder. The piston rod of a double–acting cylinder is to extend when a push button switch is actuated. The cylinder is to remain extended until a second switch is actuated and only if the first switch has been released

Name: A swivel bridge is bought into the desired position by means of a doub
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A swivel bridge is bought into the desired position by means of a double–acting cylinder. The piston rod of adouble–acting cylinder is to extend when a push button switch is actuated. The cylinder is to remainextended until a second switch is actuate

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter31: Wound Rotor Motors

Section: Chapter Questions

Problem 13RQ: Refer to the schematic diagram in Figure 318. Assume that the motor is not running. When the third...

See similar textbooks

Similar questions

Use time delay A push button is to control the forward stroke after the piston rod has reached the forward end position the components are to be pressed together for 20 seconds then the piston rod is to return automatically to the initial position Additional condition The return stroke must occur even if the start push button is still depressed A new start signl may only become effective after the initial position has been reached and after the push button has been released
It is desired to operate the pneumatic cylinder below which has to pistons A and B to stamp the die D. The piston A s returned in its back stroke by a spring, and has quick return .It is advised to use solenoid and pilot valves DCV . ( best design is to use two DCV valves ) 1- Make a complete circuit layout to operate the device above, using the appropriate symbols.2-Describe in details how your system works ( typed ) 3- Names the components of your system. 4- Any pneumatic working design will be considered as correct.
Select the proper choice(s) for each of the following statements: 1) To control single-acting cylinder we just need: double-acting cylinder we should use A2/2-way, 5/2-way, (C) 3/3-way, 3/4-way, 2) In DCV. (B) 3/2-way, 4/2-way, (D) 4/3-way, 3/2-way. mid poistion of DCV, we can move cylinder piston rod freely without resistance by hand. (A) working ports are exhausted, (C) working ports are pressurized, 3) In pneumatics we use A Compressor (B) Pump, DCV, while to control the 4) Quick exhaust valve is used to (A) increase the cylinder return speed. (C) meter-out the cylinder speed (B) all ports are closed. no one of these options. to obtain high pressure air. (C) Turbine, (D) pressure relief valve. (B) meter-in the cylinder speed, (D) increase the cylinder extending speed. 6) Meter-in of cylinder movement is used to control the Afluid that enters the hydraulic cylinder, (B) fluid that exits the hydraulic cylinder, (C) fluid that enters the DCV (D) fluid that exits the DCV. 5) One of the…
In four bar mechanism, the angle between Limiting position of output link is called O None OLimiting Position O Stroke O Throw
Name Section 5-2: Line Diagrams-Signals, Decisions, and Actions In the following application, a temperature switch controls a heating contactor and a flow switch is used to ensure there is enough air flow. If there is not enough air flow, an alarm is sounded. Complete the required information. 1. List all the signal devices in the circuit. 2. List all the action devices in the circuit. 3. List the decision part of the circuit that automatically sounds the alarm if there is a problem. 4. When the heating element is on during normal operation, is the flow switch open or closed? CIRCULATING 2 L1 FAN TEMPERATURE SWITCH TR HEATING ELEMENTS FLOW SWITCH -HOT AIR PADDLE AIR FILTER NORMALLY CLOSED FLOW SWITCH 65 ALARM (SOUNDS IF NO FLOW FOR 15 SECONDS OR MORE) Date HEATING CONTACTOR TR ON-DELAY TIMER SUPPLY AIR COLD AIR (3) TIME SET= 15 SEC © 2014 American Technical Publishers, Inc. All rights reserved
17- The memory unit of PLC is used to write the program to control output device. Select one: True False
The piston rod of a double-acting cylinder is to advance when a 3/2- way push button valve is actuated manually. The cylinder is to remain advanced until a second valve is actuated. The signal of the second valve can only take effect after the first valve has been released. The cylinder is to then return to the initial position. The cylinder is to remain in the initial position until a new start signal is given. The speed of the cylinder is to be adjustable in both directions.Draw the circuit diagram for the problem.
4. Describe two type of starting system principles and draw the basic starting circuit
FUR Y for the totowing system, calculate the mode shapes . 38 Select one Opnast © 1 0.954n* -161735/ on 1.1 f Ont.Ht
draw the symbol of a DCV the has Question positions ports 1 2 2 3 actuation solenoid+manual 3 5 left: solenoid+manual, right:pnumatic pilot+manual
Design the circuit (pneumatic/hydraulic/electro-pneumatic/electro-hydraulic) for the following problems:1.A double acting cylinder of pneumatic system will extend when two pushbuttons are pressed. The retraction is doneautomatically when either one of the pushbuttons is released.2A pushbutton is required to extend a cylinder of a pneumatic stamping machine. Once the cylinder at the full extensionposition, it will wait for 5 seconds before it is automatically retracted.3.The cylinder extends when two pushbuttons are pressed. The cylinder retracts when the set pressure of 5 bar is achieved.4.Given a hydraulic system with double acting cylinder. The cylinder extends when the lever is triggered. The retraction of thecylinder is achieved by another lever.
Which of the following statements is NOT true about limiting position (s) of a mechanism? A. A limiting position is a configuration that places the follower link in extreme location B. In limiting position configurations of slider-crank, the crank and the coupler are collinear C. In limiting position configurations of four bar linkage, the crank and the coupler are collinear D. In limiting position configurations of four bar linkage, the crank and the coupler are perpendicular None of these