A spherical gas container having an inner diameter of 5 m and a wall thickness of 24 mm is made of steel for which E = 200 GPa and v = 0.29. Knowing that the gage pressure in the container is increased from zero to 1.8 MPa, determine (a) the maximum normal stress in the container, (b) the corresponding increase in the diameter of the container. Hint: refer back to earlier notes for relationship between strain, Poisson's ratio, and stress in two directions

A spherical gas container having an inner diameter of 5 m and a wall thickness of 24 mm is made of steel for which E = 200 GPa and v = 0.29. Knowing that the gage pressure in the container is increased from zero to 1.8 MPa, determine (a) the maximum normal stress in the container, (b) the corresponding increase in the diameter of the container. Hint: refer back to earlier notes for relationship between strain, Poisson's ratio, and stress in two directions

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a temperature of 32.98 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 131.06°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 332.28 mm and M = 209 mm.
The normal strain measured on the outside surface of a spherical pressure vessel is 670 με.The sphere has an outside diameter of 1.20 m and a wall thickness of 10 mm, and it will befabricated from an aluminum alloy [E = 73 GPa;ν = 0.33]. Determine (a) the normal stress inthe vessel wall and (b) the internal pressure in the vesssel
Prob.7: [2.55] At room temperature (20°C) a 0.5 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 140°C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod. 0.5 mm 300 mm 250 mm В Aluminum A = 2000 mm E = 75 GPa a = 23 x 10-6°C a = 17.3 × 10-6PC Stainless steel A = 800 mm2 E = 190 GPa
1. A steel rod of 20 mm diameter passes centrally through a copper tube of external diameter 40 mm and internal diameter 20 mm. The tube is closed at each end with the help of rigid washers (of negligible thickness) which are screwed by the nuts. The nuts are tightened until the compressive load on the copper tube is 50 kN. Determine the stresses in the rod and the tube, when the temperature of whole assembly falls by 50°C. Take Es = 200 GPa ; Ec = 100 GPa ; as = 12 x 10-6/°C and ac = 18 x 106/°C.
A spherical gas tank is fabricated by bolting together two thin-walled hemispherical shells with an inner diameter of 8 m. The gas is pressurized to 2.0 MPa. The shells have an allowable normal stress of 150 MPa, and the 25 mm-diameter bolts have an allowable normal stress of 250 MPa. (a) Determine the minimum thickness of the walls of the tank to the nearest mm. (b) Determine the minimum number of bolts to connect the hemispheres.
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5 MPa) and is subjected to an axial force F=60 kN. Knowing that the tank has an inner diameter of 320 mm and a wall thickness of 3 mm, find the principal stresses and determine the maximum shear stress.
The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. Determine (a) the magnitude of load P. (b) the shear stress on plane AB. (c) the maximum normal and shear stresses in the block at any possible orientation. P Answers: (a) P= (b) Tnt = (c) Gmax Tmax = = i 31.5 Mi a B kips ksi ksi ksi
An aluminum rod (E = 70 GPa, α =23.6 x 10-6/°C) and steel link (E = 200 GPa, α = 11.7 x 10-6/°C) have the dimensions shown at a temperature of 20oC. The steel link is heated until the aluminum rod can befitted freely into it. The temperature of the whole assembly is then raised to 150°C. Determine the final stress in the rod and in the link.
1. The following state of strain has been determined on the surface of a cast-iron machine part: =- 720, =- 400, = 660 Knowing that E = 69 GPa and G = 28 GPa, determine the principal stresses using the following approaches: by determining the corresponding state of plane stress, and further using Mohr's circle for stress ii. by using Mohr's circle for strain to determine the orientation and magnitude of the principal strains, and further define the corresponding stresses
40 MPa PROBLEM 2.66 A 30-mm square was scribed on the side of a large steel pressure vessel. After pressurization, the biaxial stress condition at the square is as shown. For E = 200 GPa and v=0.30, determine the change in length of (a) side AB. (b) side BC, (c) diagnonal AC. 30 mn - S0 MPa 8 AR = 10.20 pm SBc = 2.40 um 8A =8.91 um
Extensometers attached to the external surface of a pressure vessel indicate that a = 0.002 and & = 0.005 along the longitudinal and transverse directions, respectively. Determine the corresponding stresses for E= 210 GPa and v = 0.4. What would be the error in these stresses if Poisson's ratio were not considered?
Q.2 A rod is made of cast iron and is secured to the piston by a tapered rod and nut and to the crosshead by a cotter. Determine the diameter of a piston rod for a cylinder of 1.3 m diameter in which the greatest difference of steam pressure on the two sides of the piston is 0.25 N/mm². The length of the rod is 2.8 m. The modulus of elasticity is 220 kN/mm? and the factor of safety is 7.