A solid steel [G= 80 GPa] shaft of variable diameter is subjected to the torques shown in Fig. Q3. The diameter of the shaft in segments (1) and (3) is 50 mm, and the diameter of the shaft in segment (2) is 80 mm. The bearings shown allow the shaft to turn freely. (a) Determine the maximum shear stress in the shaft. (b) Determine the rotation angle of pulley C to pulley A. 25 ptc 1,200 N-m 4,500 N-m CG 0.70 m (2) 1.80 m 2,800 N-m of (3) 500 0.70 m

A solid steel [G= 80 GPa] shaft of variable diameter is subjected to the torques shown in Fig. Q3. The diameter of the shaft in segments (1) and (3) is 50 mm, and the diameter of the shaft in segment (2) is 80 mm. The bearings shown allow the shaft to turn freely. (a) Determine the maximum shear stress in the shaft. (b) Determine the rotation angle of pulley C to pulley A. 25 ptc 1,200 N-m 4,500 N-m CG 0.70 m (2) 1.80 m 2,800 N-m of (3) 500 0.70 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

= BA The solid steel shaft carries the torques T₁ 750 N-m and T₂ 1200 N-m. Using L₁ L2 2.5 m and G-83 GPa, determine the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 40. (Hint: Analyze for 0 governs and T governs). Odmin 54.1 mm = Odmin 46.7 mm B Odmin = 51.9 mm Odmin 26.0 mm 7₁ B C 1₂
Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt circle 320 mm in dia- meter and six 15-mm diameter bolts on a concentric bolt circle 240 mm in diameter. Determine the unit stress in each bolt due to a torque of 25 kN.m.
The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: elastic modulus, E=200 GPa and Shear Modulus, G=75 GPa, Tb-80Nm Determine the following: a. Absolute the maximum torsional shear stress b. Angle of twist of the end B with respect to the support Show complete solution with fbd A 30 N-m 200 mm B 80 N-m 20 N-m 800 mm 600 mm
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
Required information A force P of magnitude 700 N is applied to the pedal shown. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 75 mm 9 mm 300 mm - B 125 mm 5 mm Determine the diameter of the pin at Cfor which the average shearing stress in the pin is 40 MPa. The diameter of the pin at Cis mm.
If the shaft is subjected to a uniform distributed torque of , determine the maximum shear stress developed in the shaft. The shaft is fixed at A and C. 400 mm 20 kN m/m 6o0 mm 80 mm 60 mm Section a-a
A solid circular bronze [G- 6,500 ksi] shaft, 5.4 ft long and 1.125 in. in diameter, carries a torque of 50 lb-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax psi (b) Ф-
06 ameter against Es P are Q13. A torque T = 5 kN.m is applied to a hollow shaft having the cross section shown. Neglecting the effect of stress concentrations, determine the shearing stress at points a and b. welded owable nissible 10 mm 6pm 125 mm 6 mm 10 mm 75mm Q14. A hollow member having the cross section
Question 1 of 10 View Policies Current Attempt in Progress X- K Answer: P A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 1.9 in. The shaft is subjected to a tensile axial load of P = 9 kips and torques TA = 8 kip-in. and Tg = 33 kip-in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element. > (1) H N B TB (2) - / 10 K E
The shaft consisting of steel and aluminum segments carries the torques T and 3T. Find the largest allowable value of Tif the working shear stresses are 14 000 psi for steel and 7000 psi for aluminum, and the angle of rotation at the free end must not exceed 8°. Use G= 12 x 10° psi for steel and G=4x 10° psi for aluminum. Aluminum 1 in. 2T 3 ft. Steel 2 in. 3 ft.
The solid shaft has a diameter of 0.75 in. If it is subjected to the torques shown, determine the maximum shear stress (psi) in each region of theshaft. The bearings at A and F allow free rotation of the shaft.