A solid shaft 18 m Length is to transmit power at 2200 rpm. If the shaft is stressed to 275 MPa when twisted at 40⁰, what should be the design diameter in ( mm) of the shaft and the maximum power transmitted in kW? Use shear modulus G = 100 GPa.

A solid shaft 18 m Length is to transmit power at 2200 rpm. If the shaft is stressed to 275 MPa when twisted at 40⁰, what should be the design diameter in ( mm) of the shaft and the maximum power transmitted in kW? Use shear modulus G = 100 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.4P: The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft...

See similar textbooks

Related questions

Q: A leaky 15-kg bucket is lifted from the ground to a height of 18m at a constant speed with a rope…

Q: Incorrect The 89-lb force P is applied to the 200-lb crate, which is stationary before the force is…

Q: An air conditioner with R-134a as the working fluid is used to keep a room at 23°C by transferring…

A: Given:Refrigerant in an air conditioner=R134aRoom temperature, TL=23oCOutside air temperature,…

Q: 1. Consider filling a "type A" gas cylinder from with water from a high-pressure supply line as…

Q: 13.3 Given the following information, and the Instron curve below for an axial stress experiment…

A: given; elastic modulus(E)=40MPaelongation at break(ε)=2.25initial length(l0)=1.5cmcross sectional…

Q: Q10. In the image below, the directions of the velocities of ball A and ball B before and after…

Q: 8-57. The uniform pole has a weight W and is lowered slowly from a vertical position 0 = 90° toward…

Q: Q6. Sketch the acceleration vector diagram for the engine mechanism below in fig.6, clearly…

Q: A four-cylinder, four-stroke, 2.2-L gasoline engine operates on the Otto cycle with a compression…

Q: where did you guys get the area from?

Q: Which of the following is the nearest value for the force at member CD? a. 4kN tension O b. 6kN…

Q: A brass specimen is subjected to a Tensile test in a laboratory. The following data obtained are:…

Q: 9. A compressive force of 15-N is applied to a flexible poly(vinyl chloride) (CAS# 9002-86-2) wire…

A: Write the given data. F=15 Nl=5 md=3.6 mm∆l=0.5 mm

Q: The crank AB has a constant angular velocity w. (Figure 1) Figure B 1 of 1 Part A Determine the…

A: (a) Draw the single slider crank mechanism.

Q: Find the force in member AB D E 4m a. 2kN compression b. 4kN Compression c. 2kN tension d. 4kN…

Q: 1) Half-life of cessium-137 is 30.2 years. If the initial mass of a sample of cessium-137 is 1.000…

A: The half life is defined as the time required by a substance to decay to half of its Initial Value…

Q: Would a 0.010" or 0.031" tool nose radius be stronger

Q: At the instant = 60°, the slotted guide rod is moving to the left with an acceleration a = 3 m/s²…

Q: show me how you did it so I can understand, thank you. Pls answer both, this is my last tutor…

Q: 13) In an air standard Diesel cycle, the compression ratio is 17. The cutoff ratio is 2.5:1. The air…

Q: Two cables suspend a cylinder that has a weight (W) = 150 lb. The two cables are attached to a…

A: Given: The weight of cylinder, W = 150 lb

Q: Draw the orthographic cross-section (front view) of the given image. Provide proper dimensions.

A: Find Draw an orthographic cross-section of the given object.

Q: 3. If the large ring, small ring, and each spoke weigh 90 lb, 20 lb, and 15 lb respectively. Find…

Q: Ball 1 is launched with an initial vertical velocity v₁ = 147 ft/sec. Ball 2 is launched 3.3 seconds…

Q: A particle moves along the x-axis with the velocity history shown. If the particle is at the…

Q: A. An air standard Diesel cycle rejects 10 KJ per cycle of heat while operating at 300 rpm. At the…

Q: The designer of a ski resort wishes to have a portion of a beginner's slope on which the…

A: The given information in the problem is shown in the following attached image:

Q: Determine the products of inertia about the coordi- nate axes for the unit which consists of three…

A: Now let us analyze each of mass marked 1, 2 and 3

Q: A simply supported steel beam of length L = 16 ft is loaded with two forces PA = 350 lbf and PB =…

Q: Q5. As shown in the image below, the freight cars A and B are approaching each other, and they have…

Q: a vertical hollow circular shaft of aluminum shown below fixed at the top has a load P equal to…

A: We have to find outer and inner diameter of the hollow shaft

Q: Calculate the horizontal force P on the light 14° wedge necessary to initiate movement of the 54-kg…

A: Given data θ=14°W=54 Kg =54*9.81W=529.74 Nμs=0.37

Q: The disk has a constant angular velocity of 20 rad/s Clockwise. Note that the point A is hinged at a…

A: Given: The angular speed of the disc, w = 20 rad/s The radius of disc, AB= 70 mm = 0.07 m The length…

Q: Determine the location h of the spot toward which the pitcher must throw if the ball is to hit the…

Q: Consider the figure below where force P is applied at end A of the bar ABCD. 1. What is the…

Q: Air is enclosed by a rigid cylinder con- taining a piston. A pressure gage attached to the cylinder…

A: Introduction The temperature is constant through the isothermal process from the starting condition…

Q: 1) The freebody diagram of a supporting beam is shown below. 0.3 Ra F1 Đ 0.9 UDL- 1.5 -1.3 F2 Rb…

A: Detailed explanation and solution of the above problem uploaded in below pictures.

Q: A uniform cantilever beam weighing 750-N has a smooth turning pulley attached to its free end. The…

Q: Member AB has the angular motions shown. Suppose that w = 4.5 rad/s and a = 6.7 rad/s². (Figure 1)…

Q: Water is the working fluid in a regenerative Rankine cycle with one closed feedwater heater and one…

Q: Draw the principal views on the left side of your drawing paper. Analyze the principal views and…

A: Draw the principal views of the object.

Q: what the difference between four stroke spark ignition engine and tow stroke cycle ?

A: The basic difference between 4 stroke SI engine and 2 stroke cycle is that for each power cycle the…

Q: A smooth two dimensional flat plate is exposed to a wind velocity of 100 km per hour. If laminar…

Q: Q11. As shown in the image below, the freight cars A and B are approaching each other, and they have…

Q: Ball 1 is launched with an initial vertical velocity v₁ = 173 ft/sec. Ball 2 is launched 3.2 seconds…

Q: Which of the following produces a rotation of the image frame? A. Decrease in altitude of platform…

A: The rotation of image frame takes by rotation in three direction i.e x-direction, y-direction, and…

Q: A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the…

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

Q: A piston-cylinder system contains an ideal gas. The initial conditions are T₁, P, and V. The system…

Q: The base structure of the firetruck ladder rotates about a vertical axis through O with a constant…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A thin tubular shaft with a circular cross section (see figure) and with inside diameter 100 mm is subjected to a torque of 5000 N · m. If the allowable shear stress is 42 MPa, determine the required wall thickness t by using (a) the approximate theory for a thin-walled tube and (b) the exact torsion theory for a circular bar.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29