A solid circular shaft transmits torque T= 500 Nm. Knowing that L= 300 mm, Dị = 300 mm, D2 = 250 mm and oall = 120 MPa, design the shaft using the Von Mises Yield Criterion (VM) Yiel Criterion. Draw the stress diagrams in the critical cross section.

A solid circular shaft transmits torque T= 500 Nm. Knowing that L= 300 mm, Dị = 300 mm, D2 = 250 mm and oall = 120 MPa, design the shaft using the Von Mises Yield Criterion (VM) Yiel Criterion. Draw the stress diagrams in the critical cross section.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Related questions

Q: A mild steel shaft transmits 22 kW at 550 r.p.m. It carries a central load of 900N and is simply…

A: Given Data Power, P=22KW Shaft rpm, N=550 rpm Load, P=900N Length of the beam, L=2.5m Allowable…

Q: A solid circular shaft needs to be designed to transmit a torque of 50N.m. If the allowable shear…

A: As given in question, Torque being transmitted = T = 50 Nm = 50,000 Nmm Allowable shear stress of…

Q: A hollow circular shaft with the ratio of internal and external diameters of 0.6 is required to…

Q: Q1. Explain use of Shaft and its types. Q2.Explain Design Procedure of Shaft Subjected to twisting…

A: 1.Uses of shaft A shaft is a rotating machine component, typically circular in cross section that is…

Q: solid circular shaft rotates at 200 rpm and transmits power of 112 kW. Calculate the minimum…

A: Given, Rotational speed of shaft = N = 200 rpm Power transmitted = P = 112 kW = 112,000 W Allowable…

Q: PROBLEM 3. A solid cross-section shaft made of A992 steel and having a diameter of 60 mm is fixed at…

A: Given data as per question The diameter of shaft =60 mm Torque applied in AC =500 N.m/m Torque…

Q: A hollow cylindrical shaft has an internal diameter of 100 mm, an external diameter of 130 mm and is…

A: As per the given data in the question, the given answer is not correct. Please find the attached…

Q: The allowable shear stress in two steel (G = 83 GPa) shafts below is 90 MPa. The design requires…

A: Given data, Shear modulus of the shaft, G = 83 x103 MPa Allowable shear stress, ?allow = 90 MPa…

Q: Circular solid ACB shaft is fixed supported between the wall at A and B. If the allowable shear…

A: Allowable shear stress τallowable=42 MPa=42×106 N/m2Let the maximum torque applied at section C be…

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: To find: The diameter of the shaft. Given: The torque T is T=420 Nm. The allowable shear stress of…

Q: Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B.…

Q: An automotive shaft manufacturing facility wants to reduce the material cost of the shaft. Propose a…

A: When we want the shaft to carry shear stress on the outermost edge, the most preferred one is hollow…

Q: 04- A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: Two designs for a shaft are being considered. Both have an outside diamete of 80 m and are 100 cm…

Q: A hollow aluminum shaft with an outside diameter of 80 mm and a wall thickness of 5 mm has an…

Q: The internal loadings at a critical section along the steel drive shaft of a ship are calculated to…

A: Given data: The torque, T = 2300 lb-ft. The bending moment, M = 1500 lb-ft. The axial trust, P =…

Q: a hollow shaft for a rotary compressor is to be designed to transmit maximum torque of 4750 n-m. the…

A: Given Data⇒ Hollow shaft Maximum torque : Tmax=4750 N-m Shear stress in shaft : ζ=50 Mpaζ=50×106Pa…

Q: Task 3: A hollow aluminum alloy 6061-T6 shaft of outer radius c = 40 mm, inner radius b = 30 mm, and…

A: Given data:

Q: A hollow shaft transmits 7 MW at 200 rev/min. It is supposed that the maximum allowable stress is…

A: Given, P=7 MW=7×106 WN=200 RPMτ=70 MN/m2=70×106 N/m2G=80 GN/m2=80×109 N/m2θL=0.40/m=0.4×π180…

Q: Torsion Problem 6.0 A solid steel shaft is to transmit 5 hp from the motor to which it is attached.…

Q: Question: A solid shaft is transmitting 1 MW at 240 r.p.m. Determine the diameter of the shaft if…

A: Given data: P=1 MWN=240 rpmTmax=1.2Tmτmax=60 MPa Need to determine the diameter of the shaft.

Q: A solid steel shaft ABCDE turns freely in bearings at points A and E. The shaft is driven by the…

Q: hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner dieter of 1.5 in. The…

Q: A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the…

Q: A solid steel shaft is subjected to torsional loadings. If T=10 kN-m. T= 45 MPa, the diameter of the…

Q: A hollow shaft for marine applications has outer and inner diameters of 400 mm and 200 mm…

A: Given: The outer diameter of shaft, D = 400 mm = 0.4 m The inner diameter of shaft, d = 200 mm = 0.2…

Q: Question 4 A shaft used for a water pump has a diameter of 50 mm and a length of 0.7 m long and is…

A: GIVEN DATA- a) Diameter D=50mm , L=0.7m , G=90GPa , Torque T=1200Nm b) Hollow shaft with internal…

Q: A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the…

Q: SS 304 steel shaft is 3 m long and has an outer diameter of 60 mm. When it is rotating at 60 rad/s,…

Q: (6) A solid shaft is used to transmit 75kW @ 550rpm. If the shaft design stress will not exceed…

Q: A solid circular shaft needs to be designed to transmit a torque of 50Nm. If the allowable shear…

A: GIven DataT = 140 mPaFOS = 2T = 50 N.mTo find diameter

Q: A solid circular shaft has a diameter d and subjected to a bending moment M and torque T. The shaft…

A: Given data The diameter of solid shaft = d Bending moment = M torque = T yield strength of…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Given, Diameter of shaft = d = 100 mm Axial stress = σx = 50 MPa = 50 N/mm2 Torque = T = 10 kNm = 10…

Q: (6) A solid shaft is used to transmit 75kW @ 550rpm. If the shaft design stress will not exceed…

Q: A shaft supported at the ends in ball bearings carries a straight tooth spur gear at its mid span…

Q: A solid shaft has to transmit 120 kW of power at 160 rpm. If the shear stress is not to exceed 60…

Q: A 3 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of 200 HP. The shaft…

A: Given data as question Length of shaft = 3 feet Power of shaft = 200 hp Sped of shaft = 1500 rpm…

Q: The solid 35-mm-diameter shaft is used to transmit the torques applied to the gears. The shaft is…

A: Given data: To determine the maximum torque, draw the torque diagram for the given system. Thus,…

Q: A solid shaft is to transmit 250 kW at 180 rpm. The torsional shear stress is not to exceed 110 MPa.…

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

Q: solid steel shaft has a diameter of d and a length of L had used to transmit a power of 120 kW at…

Q: PROBLEM 3.2 Determine the maximum shear stress caused by a torque of magnitude T= 800 Nm. [Ans. 87.3…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

Q: TUEMS 4 Let's consider a solid circular shaft subjected to the torque loads as showns Determine the…

A: Calculated the minimum required diameter of the shaft in mm.

Q: Detailed solution would be appreciated thanks!!. The steel shaft is formed by attaching a hollow…

Q: A solid circular shaft has a diameter of d mm and is made from steel, which fail when tested in…

A: Given:Syt=150 MPaM=22.2 KN.mT=44.4 KN.m

Q: A 3-meter solid steel shaft, with an unknown diameter, twists by 5° as it experienced a shear stress…

A: GIVEN DATA- L=3m Angle of twist =5' Shear stress =60MPa G=83GPa

Q: roblem 1. The internal loadings in shaft are calculated to be a torque of 3500Nm, a bending homent…

Q: Q3-C- The 304 stainless steel shaft with modulus of rigidity 75 GPa and 3 m long has an outer…

A: Calculated the smallest thickness of shaft.

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

A solid circular shaft transmits torque T= 500 Nm. Knowing that L = 300 mm, Dị = 300 mm,
D2 = 250 mm and oall = 120 MPa, design the shaft using the Von Mises Yield Criterion (VM) Yield
Criterion. Draw the stress diagrams in the critical cross section.
B
F
L
L
L

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Assume TA = 532 N-m, Tg = 1330.0 N-m, Tc= 1064 N-m, and Tp = 266.0 N-m. Determine the magnitude of the maximum shear stress in the shaft. Answer: Tmax= i D Tp (3) C Tc MPa (2) B TB (1) TA
A circular cross section shaft has a diameter of d = 45 mm, is subjected to a combined state of loading defined by M = 1.6 KN.m bending moment and T = 2.1 KN.m torque. If the material is steel 1020HR, What will be the safety factor using : (a) The maximum shearing stress theory (MSS). (b) The distortion energy theory (DE-Von Mises)
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
The 60-mm-diameter shaft is made f 6061-T6 aluminum. (Figure 1) Figure 1.20 m 1.20 m T 1 of 1 > Part A If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.060 rad, determine the maximum allowable torque T. Express your answer to three significant figures and include the appropriate units. μÄ T= 5.089 Submit C kN•m Provide Feedback Previous Answers Request Answer ? * Incorrect; Try Again; 4 attempts remaining
What is the minimum diameter of a solid steel shaft that will not twist through more than 3˚ in a6-m length when subjected to a torque of 15 KN-m? What maximum shearing stress isdeveloped? Use G=85 GPa.
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. (Figure 1) It is subjected to the torque T = 1.7 kN-m. Figure A T 800 mm B 600 mm. 1 of 1 Part A Determine the maximum shear stress in region AC. Express your answer to three significant figures and include appropriate units. (Tmax) AC= Value Submit Part B μÀ Request Answer Submit (Tmax) BC= Value Determine the maximum shear stress in region CB. Express your answer to three significant figures and include appropriate units. HÅ < Return to Assignment Request Answer 6 Units + ? Units Provide Feedback C IWC ?
A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3200 lb-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 610 rpm? What is the maximum shear stress developed in the shaft? Answer: P = i T = i hp psi
Two designs for a shaft are being considered. Both have an outside diameter of 80 m and are 100 cm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque (T) = 199.