A short post constructed from a hollow circular tube of aluminum supports a compressive load of 54 kips. The inner and outer diameters of the tube are d1=3.6 in. and d2=5.0 in., respectively, and its length is 40 in. The shortening of the post due to the load is measured as 0.022 in. Determine the compressive stress and strain in the post. (

A short post constructed from a hollow circular tube of aluminum supports a compressive load of 54 kips. The inner and outer diameters of the tube are d1=3.6 in. and d2=5.0 in., respectively, and its length is 40 in. The shortening of the post due to the load is measured as 0.022 in. Determine the compressive stress and strain in the post. (

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.2P: A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas....

See similar textbooks

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The bar ABC shown is loaded by a force P1=20 kN and P2= 40 kN at points C and B respectively. The bar has a constant axial rigidity of 120 x 10^6 N. A. Determine the strain energy of the bar when the force P1 acts alone (P2=0)B. Determine the strain energy of the bar when the force P2 acts alone (P1=0)C. Determine the strain energy when the forces P1 and P2 are acting simultaneously upon the bar.
A circular tube AB is fixed at one end and free at the other end. The tube is subjected to axial force at joint B. If the outer diameter of the tube is 5 in. and the thickness is 3 - in., calculate the maximum normal stress in the tube (in ksi). (Include the sign of the value in your answer.) A 6 ft ed = 5 in. В V8 kips t= 3/4 in. 2.5 in. ksi
The rectangular piece of wood, 50 mm by 100 mm, is used as a compression block. The grain of the wood makes a 20° angle with the horizontal, as shown in Figure 2. Determine the largest axial force P that can be applied safely if the allowable stresses on the plane of the grain are 20 MPa for compression and 5 MPa for shear. IP 20°
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
2. The tires of an agricultural tractor shown below are assumed to be 25 cm wide for the front tires and 40 cm at the rear tires. Ground contact of each tire is 15 cm. Calculate the compressive stress between each tire and the ground surface. Weight = 2,500 kg 15 cm 1.3m Point A 2.2 m 2R 2F
Question 1 The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 × 10-3. If Esteel = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as -3800 μm/m. Use the dimensions L₁ = 1900 mm, L₂ = 1425.00 mm, a = 190 mm, b = 380 mm, and c=143 mm. Determine: (a) the normal strain in bar (1). (b) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin C before the load is applied. (c) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin B before the load is applied. L₁ Answer: (a) &₁ = (b) E₁ = A i i (c) E₁ = i 1 1 1 a B (1) b Rigid bar L2 με με με C (2)
The bar shown in diagram is subjected to a tensile load of 150 kN. If the stress in the middle portion is limited to 160 N/mm2, determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 0.25 cm. Young's modulus is given as equal to 2.0 × 105 N/mm2. 150 KN ➜ 10 cm DIA 45 cm 10 cm DIA 150 KN
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με
A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is heated and shrunk to a steel wheel 800.5 mm in diameter. The modulus of elasticity E = 200 MPa. a. Determine the tensile stress in the tire. b. Determine the compressive pressure between the tire and the wheel. c. Determine the thickness of the tire to resist a pressure of 1.5 MPa if it has an allowable stress of 124 MPa. I need answer ASAP. Thank you!