A sample of an ideal gas is in a vertical cylinder fitted with a piston. As 5.79 kJ of energy is transferred to the gas by heat to raise its temperature, the weight on the piston is adjusted so that the state of the gas changes from point A to point B along the semicircle as shown in the figure. Find the change in internal energy (in J) of the gas. P(kPa) 500+ 300+ JA 0. V (L) 1.2 3.6 6.0

A sample of an ideal gas is in a vertical cylinder fitted with a piston. As 5.79 kJ of energy is transferred to the gas by heat to raise its temperature, the weight on the piston is adjusted so that the state of the gas changes from point A to point B along the semicircle as shown in the figure. Find the change in internal energy (in J) of the gas. P(kPa) 500+ 300+ JA 0. V (L) 1.2 3.6 6.0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the diagram, the state of helium gas is changed in such a way that its PV graph is a straight line segment with volume Vo increases to yVo and pressure Po increases to xPo where x and y are arbitrary constants. During this process the total heat transferred to the gas is equal to the heat necessary to double the absolute temperature of the gas at constant volume. What is the maximum ratio for the volume increase? xP, P. Vo
One kg. of gas is confined to a constant volume tank. Initial pressure and volume are 4 0.21m3 respectively. When a heat energy of 82 kJ is supplied to the system, the final temperature of the gas becomes 127 degrees C. Find (a) Work done. (b) Change in internal energy. (c) Specific heat at constant volume. Assume, R=300 Nm/kgK.
A piston and cylinder device contains 0.15 kg of water at 25◦C (state 1). As shown in the figure, the piston weighs 500 N and has a cross-sectional area of 0.01 m2. Atmospheric pressure is 100 kPa. Heat is transferred to the cylinder from a reservoir at 200◦C, raising the piston. When the piston touches the stops, the volume inside the cylinder is Vmax= 0.165 m^3 (state 2). Heat continues to be transferred until the control mass reaches the boundary temperature (state 3). Determine: a) The initial pressure of the water (kPa) b) The temperature (Celsius) when the piston hits the stops c) The total work (kJ) d) The total heat transfer (kJ) e) The total entropy production for the entire process (kJ/K)
One kilogram of air is compressed from a volume of 1.0 m and a pressure of 100 kPa to a volume of 0.147 m and a pressure of 1000 kPa. Assuming that the compression follows the law pu" the work done during the compression process. = constant, find
He gas undergoes adiabatic expansion at P1 = 8 bar, T1 = 750K to T2 = 400K. Then, the gas is heated at constant P back to T3 = 750K. If the process is to be replaced by a single isothermal expansion step to an arbitrary pressure P, what value of P (in bar) will result to the same work as the original process? Assume helium is an ideal gas with constant heat capacity. a.1.56 b.0.90 c.2.49 d.1.66
4. Consider an engine that has a piston in the cylinder that can ignore friction. The bore (diameter) of the piston is 100mm. 3 MPa of gas in the engine cylinder expanded and the final pressure became 0.1 MPa. At this time, the moving distance of the piston is 80mm, and it is said to expand in a process indicated by a straight line on the P-V diagram. Find the day of expansion (kJ) in this process.
A fluid is contained in a cylinder by a spring-loaded, frictionless piston so that the pressure in the fluid is linear function of the volume (p = a + bV). The internal energy of the fluid is given by the following equation U = 34 + 3.15 pVwhere U is in kJ, p in kPa and V in cubic metre. If the fluid changes from an initial state of 173 kPa, 0.03 m3to a final state of 400 kPa, 0.06 m3, with no work other than that done on the piston, find the direction and magnitude of the work and heat transfer.
wer.. 2. Ammonia weighing 22 kgs is confirmed inside a cylinder equipped with a piston has an initial pressure of 413 KPa at 38C. If 2900 KJ of heat is added to the ammonia until its final pressure and temperature are 413 KPa and 100C, respectively, what is the amount of work done by the fluid in KJ?
The frictionless piston and cylinder contain 1 kg of water. The initial pressure and volume are each pressure of 100kPa 0.25 m^3 (state 1). The system was gradually heated and when the volume of water in the cylinder became four times the initial volume (state 2), the piston was fixed and heating was continued until the water pressure reached 300 kPa (state 3). (1) Find the final temperature in the cylinder (2) Find work during this process (3) Find the amount of heat transfer during this process. Try to approximate this process on a P-v diagram.
A perfect gas has a value of R = 58.8 ft-lb/lb-R and k = 1.26. If 20 BTU are added to 5 lb of this gas at constant volume when the initial temperature is 90 F, find the final temperature
H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is ¼ time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k
5 kg of steam occupies a volume of 10 m^3. Find the quality if the temperature is measured at 75 C.