A reinforced concrete slab (one-way slab design-one ends continuous) is built integrally with its supports and consists of two equal spans, each with a clear span of 17 ft. The service live load is 210 psf, and 4000 psi concrete is specified for use with steel with a yield stress equal to 60,000 psi. What is the thickness and weight of the slab? Minimum thickness h of nonprestressed one-way slabs Simply supported One end continuous Both ends continuous e/20 /24 /28 /10 Cantilever O a. 8.50 (in), 106 (psf) O b. 9.50 (in), 152 (psf) O c. 8.50 (in), 91 (psf) O d. 9.50 (in), 128 (psf)

A reinforced concrete slab (one-way slab design-one ends continuous) is built integrally with its supports and consists of two equal spans, each with a clear span of 17 ft. The service live load is 210 psf, and 4000 psi concrete is specified for use with steel with a yield stress equal to 60,000 psi. What is the thickness and weight of the slab? Minimum thickness h of nonprestressed one-way slabs Simply supported One end continuous Both ends continuous e/20 /24 /28 /10 Cantilever O a. 8.50 (in), 106 (psf) O b. 9.50 (in), 152 (psf) O c. 8.50 (in), 91 (psf) O d. 9.50 (in), 128 (psf)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam weight) which will cause the section to begin to crack if they are used for 28 ft simple span. = 4000 psi , the modulus of rupture f, = 7.5f',, and reinforced concrete weight is 150 lb/ft³. 15" 18" 2 #8 3" 12"-
An RCC beam having 200 mm wide and 400 mm effective depth is reinforced with Fe415 grade steel of area 1000 mm² in tension. Assume M20 grade concrete, what is approximate value of the depth of neutral axis for the equilibrium of forces at the limit state of collapse? (a) 200 mm (c) 300 mm (b) 250 mm (d) 350 mm
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPa. a) Maximum Steel ratiob) Tension Forcec) Compression Force
B. If f'c 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in Ib/ft? 250 mm 80 mm 130 mm 80 min 80 mm
What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all depth of 536 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 75 mm. The specified compressive strength of concrete is 22.00 MPa. The yield strength of tension reinforcements and stirrups are 404 MPa and 323 MPa respectively.
Design strength for M25 concrete in direct compression, bending compression and flexural tension are, respectively A 10 MPa, 11.15 MPa and 3.5 MPa B 25 MPa, 11.15 MPa and 3 MPa с 10 MPa, 12.5 MPa and 3.5 MPa D 25 MPa, 11.15 MPa and 2.57 MPa
PROBLEM: A rectangular reinforced concrete beam has a width of 310 mm and an effective depth of 490 mm. Concrete compressive strength (fc') is 21 MPa, and steel yield strength (fy) is 345 MPa. Use USD Method. DETERMINE: 1. Ultimate moment capacity if the beam is reinforced with 4– 25 mm diameter tension steel. 2. Ultimate moment capacity if the beam is reinforced with 5 – 25 mm diameter tension steel. 3. Ultimate moment capacity if the beam is reinforced with 6 – 25 mm diameter tension steel. 4. Ultimate moment capacity if the beam is reinforced with 8 – 25 mm diameter tension steel. 5. Ultimate moment capacity if the beam is reinforced with 10 – 25 mm diameter tension steel.
A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]
A beam subjected to weather upon concrete pouring has a dimension of approximately 310 mm by 555 mm which is reinforced with 4-Ø28 mm bars for tension laid in a single layer with Ø10 mm for stirrups. Determine the following if the concrete compressive strength is 30 MPa and the steel yield strength is 415 MPa. a. Are there any code provisions violated by the actual beam if it is assumed to be singly? State the provision that has been violated. b. If the beam violated a code provision, redesign a smallest single layer singly reinforced beam using the moment capacity of the original beam. (Use same parameters such as dimensions, main bar diameter, stirrups diameter, concrete compressive strength and steel yield strength). c. Redesign a smallest single layer singly reinforced beam using the ultimate moment capacity of the given beam corrected for its violation of the code. (if there are any violation)
A simply supported one way reinforced concrete floor slab has a span of 4 m. It carries a service live load of 9 kPa and a service dead load of 2 kPa. =21 MPa, =415 MPa. Use clear concrete cover of 20 mm.a) Determine the spacing of 16 mm main bars of the slab for minimum thickness as specified by the NSCP 2015.b) Determine the spacing of the 12 mm shrinkage and temperature bars for minimum thickness of slab.c) Determine the spacing of the 16 mm main bars of the thinnest possible slab allowed by the NSCP 2015.
A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm
Given Beam Data: Slab Thickness, t=175 mm Effective Depth, d= 300 mm Width of web, bw = 250 mm Material Properties Concrete, fc-24 MPa Steel, fy = 415 Mpa The concrete slab has an equivalent width of 600 mm and casted monolithically with the beam Assume that the steel bars will be distributed in one layer only and use 2010 NSCP. a) Detemine the balanced steel ratio of the section in positive bending b) Determine the maximum steel ratio for the beam in positive bending for failure in tension. c) If the slab has a thickness of 100 mm and the equivalent width of the concrete flange from the slab is 1200 mm, detemine the balanced steel ratio of the section for positive bending d) Determine the steel ratio if the section is used for negative bending