A lighting load of 2 MW and a motor load of 4 MW at 0.8 pf lagging are  supplied by two alternators operating in parallel. If one of them is  delivering a load of 2.4 MW at 0.95 pf lagging, what will the output and pf  of the other alternator.

Q: p-flops (b) Design a 3-bit counter for the sequence given in Figure Q.4.3 using D flip-flops and bas...

A: We need to design the given counter by using of D flip flop

Q: In a 110 V compound generator, the resistances of armature, shunt and series field windings are 0.06...

A: Compound Generator The compound generator consists of both series field winding and shunt field wind...

Q: The modulating signal that is the input into an FM modulator is m(t) = 2cos (10nt). a) Express the t...

A: The answer as given below steps;

Q: D 10.19 Design a CS amplifier for which the MOSFET is operated at g, = 5 mA/V and has C, =5 pF and C...

A:

Q: E2.27 Find V, in the circuit in Fig. E2.27. I + 2VA A 4 kN 6 V(+ 8 kN Vo Figure E2.27

A:

Q: Ex. 140. Assume all mks units in Figure 140. Determine the loop currents: I1, 12, 13 when V1=-7, V2=...

A: This question belongs to circuit theory . It is based on the concept of mesh analysis in the circuit...

Q: (a) Consider the minterm function F(A, B,C) = Em(1,3,4,7) %3D Implement the circuit using 4-to-1 and...

A: Given that function∑m1,3,4,7

Q: 20: Given ddc=0.98 , determine Bac O Given Pdc=120 , determine the coriesponding valve of d. Te=2:0m...

A: Part (a)  - Given that,αdc = 0.98We know,The expression for β is givem by,β=α1-α  --(A)  

Q: 49. Which of the following is true for first-generation wireless systems?

A: In this case, from the given options, the correct option related to the first generation cellular sy...

Q: (b) Figure Q3(b) shows a magnetic circuit with two different material, with a mean cross- sectional ...

A: Given information about the magnetic (core) circuit with two different material is Cross sectional a...

Q: 4.86 A clamped capacitor using an ideal diode with cathode grounded is supplied with a sine wave of ...

A:

Q: PROBLEM SOLVING: Solve for what is being asked given the circuit below. Show complete, neat and orde...

A:

Q: or the voltage-divider configuration of the figure below: a) Sketch the DC equivalent circuit b) Det...

A:

Q: 3.63 In the circuit shown in the image below, if 4 = 5.6 A and R1 current io in A. = 12 Q, determine...

A:

Q: TH UTM e (c) Figure Q.3.2 shows a 3-bit ripple-carry-adder for S= A + B. Modify the adder 8 UTM O to...

A: Note:  As per the  guide lines of the bartleby we are supposed to solve one question, when they are ...

Q: Question-1: The induced magnetic force, given by Find = i (L x B), is called motor action and the in...

A: a. This induced forces in generator is there to counter the input forces applied by prime mover. Thi...

Q: 2.112 Determine the value of V, in the network in Fig. P2.112. 12 kN 6 kN 18 kN 4 kN 6 kN Vo

A:

Q: 1. IfI = 50230° A, calculate I, and I2 by using current divider rule. 2. Calculate total impedance Z...

A:

Q: Determine the equivalent resistance, Req if X=9 b) Determine current i, if "R" is 20 ohms.

A: The solution can be achieved as follows.

Q: In the unbalanced bridge circuit of the given figure, find the potential difference that exists acro...

A:

Q: Question 4b Magnetic fields are characterized by the existence of a detectable magnetic force at eve...

A: According to the question, we need to discuss one of the industrial applications of the magnet.

Q: 1.8 (a) In the circuit of Fig. P1.8 find v, for the follow- ing cases: v, = 0 V, v, = ±3 V, and v, =...

A:

Q: B) i) Sub. 5 from 12. Use l's complement. ii) Add, 22 to -47 in binary. Use 2's complement. iii) Add...

A:

Q: torminals 1,2 ops0.22 terminals 3,4 R=0.22 torminols 576 R= 2952 termials 7.8R=2,8R 24V 2 3. 12ov ka...

A: Given: Transformer rating: 240 V, 60 Hz Terminal 1, 2: R12=0.2 ΩTerminal 3, 4: R34=0.2 ΩTerminal 5,...

Q: A 5hp, 220V, 24.08A, 60 Hz, single-phase induction motor with power factor 0.8 lagging. What is the ...

A: After capacitor insertion the motor draws only active power from the supply and total  reactive powe...

Q: 1. Find VAB in the given network: 20 V 4 R1 25 2 R2 40 2 VAB R3 15Q R4 10Ω

A: In this question,  Find the voltage across the A and B.  We are using the voltage division method.  ...

Q: A depletion MOSFET has IDSS = 10 mA and VP = – 4.5 V. Calculate the drain current at a gate-source v...

A:

Q: -j12.8 N HE a j12 N 93 Yab 350 j10 Q -j2 N 34 N b. 13.6 Q HE

A:

Q: 13.8 Find the poles and zeros of the impedance seen looking into the terminals a,b of the circuit sh...

A:

Q: 20: Given Ldc=0.98 , determine Bodc: Pdc O Given Pdc=120 , determine the cormesponding value of d. ©...

A:

Q: 2. Use KCL and KVL to: a. Establish the current equations at points x and y b. Establish the voltage...

A:

Q: A coil has a resistance of 14 Q at 50°C. If the temperature coefficient of resistance at 0°C is 0.00...

A: Given a coil has, AT temperature, T1=50 °C Resistance, R1=14 Ω Temperature coefficient at 0 °C is, α...

Q: 2 ka Si +10 Vo 2 k2 2 ka

A:

Q: Example: Find Thévenin's equivalent circuit between a &b for the network in Fig. 2.32. Then find the...

A:

Q: In the magnetic circuit of Fig. 6.49, the core is composed of annealed sheet steel for which a stack...

A: Given stacking factor =0.9 core thickness =5 cm core width = 3 cm  

Q: 2. a) Because of its barrier potential, can a diode be used as a voltage source? Explain b) What wou...

A: The potential barrier in a very tangency may be a sort of barrier that stops traditional charge flow...

Q: Using the De N TMS thTM convert the SOP Boolean equation: complement. What is the range of values fo...

A:

Q: Consider a 1000-W iron whose base plate is made of 0.5-cm-thick aluminum alloy (p= 2770 kg/m3 and cp...

A: Please refer the attached images for the complete answer..

Q: QUESTION 15 For the step down transformer below the turns ratio is 5: 1, the primary voltage is 122 ...

A:

Q: (a) Consider the minterm function F(A, B, C) = Em(1,3,4,7) Implement the circuit using 4-to-1 and 2-...

A:

Q: TRUE OR FALSE) - Energy conversion of DC generator is based on the principle of production of dynam...

A: This question belongs to electrical machine . It is based on the working of dc generator and dc moto...

Q: 6. What is the locus of the points define

A: Here z is a complex form which is denoted as (x+iy) . Conjugate of z = (x-iy).

Q: Example 5 – For a non-ideal amplifier and the foll parameters, Input signal power = 2x10-10W Input n...

A:

Q: An a.c. generator consists of a coil of 1000 turns and cross-sectional area of 3m2 , rotating at a c...

A: Given: An a.c. generator consists of, Number of turns, N = 1000 turns Cross sectional area, A = 3 m2...

Q: 4.90 A reverse-biased photodiode is specified to have a dark current of 100 pA and a responsivity of...

A:

Q: Determine ond sketch ir and Vo for the clipper eircwit V; lov lokn V si si V. -lov Vi 5. 7.3V 五 |

A:

Q: 6.7 In cylindrical coordinates, V = 0 at p = 2 m and V = 60 V at p = 5 m due to charge 10 distributi...

A: GIVEN:               (1)    V=0 at p=2m                      V=60V at p=5m                     ρr=10...

Q: 14. An industrial plant hes a load of 800 kw at a power factor of 0.8 lagging. It is desired to purc...

A:

Q: complete the timing Vlagram in Figure Q.4.2 for A and B. Figure Q.4.2 UTM (a) Figure Q.4.1 shows a n...

A:

Q: V1 j4 2 V2 + Vx 220° A -j3 N 3Z45° A 5Ω

A: "As per our guidelines, we are supposed to answer only one question. Kindly repost the other questio...

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.