A large artery can have a diameter of about 0.5 cm, whereas a large vein may have a diameter of about 0.8 cm. The average blood velocity in these arteries and veins is, respectively, on the order of 40 and 20 cm sec-!. Calculate for these blood flows the wall shear rate, yw. What would the shear rate be at the centerline of these blood vessels?

A large artery can have a diameter of about 0.5 cm, whereas a large vein may have a diameter of about 0.8 cm. The average blood velocity in these arteries and veins is, respectively, on the order of 40 and 20 cm sec-!. Calculate for these blood flows the wall shear rate, yw. What would the shear rate be at the centerline of these blood vessels?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(4) Three cast iron pipes are laid in parallel with the dimensions given in the table below: Pipe Length, m Diameter, cm 1 800 12 600 8 3 900 10 Take water density p 998 kg/m and dynamic viscosity u = 0.001 kg/(m.s). The total flow rate is 200 m'/hr of water at 20°C. By using the pipes in series equations along with either the Moody chart or the Colebrook iteratively, determine (a) the flow rate in each pipe, and (b) the pressure drop across the system.
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
Q.4 A 200 mm diameter pipeline is laid on the ground. At a particular point, the piezometric head is 20 m. Total energy head of water at a point is 26 m. The Discharge (L/s) of water through the pipe is Type your answer here.. SUBMIT
(a) Suppose we have planned to design a hydraulic system.ln this aspect, the pump selection is to be finalized for a flow rate of 3907 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.4 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. (b) Write the significance of using minimum diameter pipelines in the hydraulic system. (a) Area of the maximum sized pipe diameter (in m?) (b) Area of the minimum sized pipe diameter (in m2) (c) The minimum sized pipe diameter (in m) (d) The maximum sized pipe diameter (in m)
A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle B2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles. What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient noo = 1. 91.84 65.60 46.86 128.58 180.01
Air at 1 atm and 20 C flows through a smooth pipe. The centerline velocity and the pipe diameter are 6 m/s and 15 cm, respectively. Find a) the wall shear stress and b) the average velocity in the pipe.
Water is flowing at 0.075 cu.m./sec through a glazed porcelain pipe 400m long and 200mm diameter. The pipe roughness is 0.0015mm. Properties of water: Density: 1,000 g/cu.m., viscosity = 0.001 N-m/sec. What is the velocity of water in the pipe? What is the Reynold's number? Steady State flow exists in pipe that undergoes a gradual expansion from a diameter of 6in. Assuming constant density and the inlet flow velocity is 22.4 ft/sec. What is the size of the exit pipe if the exist flow velocity is 12.6 ft/sec?
A storage tank contains a liquid at depth y where y= 0 when the tank is half full. Liquid is withdrawn at a constant flow rate Q to meet demands. The contents are resupplied at a sinusoidal rate 3Q sin'(t), The outflow is not constant but rather depends on the depth. For this case, the differential equation for depth is shown below. Some variable values are A = 1200 m?, Q = 500 m /d, and a (force function) = 300. Arrange the variables into the Mathematical Model format: stating which variable(s) is dependent, independent, etc. dy a(1+ y)15 dx A Figure P1.7
A) A 0.4 m diameter fan running at 970 rev min' is tested when the air temperature is 10 °C and the barometric pressure is 772 mm Hg and the volume flow rate Q=0.7 m s. Find the corresponding volume flow of a geometrically similar fan of 1 m diameter, running at 500 rev min at same conditions. Assume that the fan efficiency is unchanged. Ja
The resistance for flow through all feed arteries (assume N=2,000,000 feed arteries) can be estimated using Poiseuille's Law. Assume a single feed artery has length L=0.5cm ; radius r=0.004 cm and blood viscosity n=0.02 Poise (gr/cm/s). Estimate the Resistance to blood flow that these 2,000,000 parallel feed arteries contribute in mmHg/Lt/min. answer choices R = 1.24x106mmHg/Lt/min R= 0.62 mmHg/Lt/min R= 0.51 mmHg/Lt/min R = 1.2x104mmHg/Lt/min %3| %3D
A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle B2 is 158* and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles. What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient n = 1. 91.84 65.60 46.86 128.58 180.01 calculate the water horsepower. 52.4 22.1 78.9 16.8 34.8
Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be finalized for a flow rate of 3464.5 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.6 m/s and 6.8 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines.