A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 4 m² and a large one of cross-sectional area 25 m² (a) If this lift is designed to raise a 3500 kg car, what minimum force must be applied to the small piston? (b) what must be the minimum pressure applied to the small piston?

A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 4 m² and a large one of cross-sectional area 25 m² (a) If this lift is designed to raise a 3500 kg car, what minimum force must be applied to the small piston? (b) what must be the minimum pressure applied to the small piston?

Name: 3. A hydraulic lift in a garage has two pistons: a small one of cross
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. A hydraulic lift in a garage has two pistons: a small one of cross-sectional area 4 m² and a large one of cross-sectional area 25 m² (a) Ifthis lift is designed to raise a 3500 kg car, what minimum force must be applied to the small piston? (b) w

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The input and output pistons of a hydraulic car lift have diameters of 3.00 in and 25.0 in, respectively. A 2890 lb car is raised through a height of 5.00 ft above the garage floor. (a) What is the input force? (b) What is the distance through which the input piston moves?
A 500kg bucket is lifted by a crane at a certain position shown below. What is the magnitude of the force that is exerted on the hydraulic piston?
A semicircular floodgate is 4.0 m long and 3.0 m radius. It is articulated at its lower point and has a latch at its top point. disregarding the weight of the gate, what will be the reaction forces on the latch and joint? NA
QUESTION 10 In a hydraulic car lift, the input piston has a radius of 2 cm and a negligible weight. The output plunger has a radius of 0.4 m. The combined mass of the car and the plunger is 1.2 tonne. The hydraulic lift uses hydraulic fluid. What input force (in N) is needed to support the car and the output plunger when the bottom surfaces are at the same level?
Figure shows a set-up with a vessel containing a plunger and a cylinder. What force, F is required to balance the weight of the cylinder. If the weight of the plunger is negligible?
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 45 100 Ib te-18 15 3 ft 3 ft- 30 200 lb ft 30 30 30 kg 2 ft B 12 Fig (1) Fig (2) Fig (3)
In a car service station, a force of 100 N is required to raise the car on the hydraulic lift. If the diameter of the hydraulic lift is 20 times as the radius of the piston where the force must be applied, what is the mass of the car to be lifted?
Calculate the forces, in Newtons, for the following:(d) member FG(e) pin H(f) hydraulic cylinder AB
The small piston of a hydraulic press has a cross-sectional area of 3cm2, and its larger piston has a cross-sectional area of 200cm2. What downward force must be applied to the small piston for the lift to raise a load of 15KN?
(5) A B $15⁰ 6 in. 100 lb D C E What is the horizontal force on block E applied by the slider D if a = 4 in.? The slider is on wheels and can translate without friction. Draw free body diagrams of ABC and BD.
H.W3/3.6/Page(92) As shown, a mouse can use the mechanical advantage provided by a hydraulic machine to lift up an elephant. a. Derive an algebraic equation that gives the mechanical advantage of the hydraulic machine shown. Assume the pistons are frictionless and massless. b. A mouse can have a mass of 25 g and an elephant a mass of 7500 kg. Determine a value of D1 and D2 so that the mouse can support the elephant. Elephant with mass m2 Mouse with mass m Piston (2 places) Hydraulic fluid D2
Required Information A hydraulically powered lift supports the two boxes shown. Each box weighs 150 lb with center of gravity in the middle of each box. Neglect the weight of Individual members. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. F H -2 ft--2 ft· E 4 ft A B Di T 2 ft C -3 ft2 ft- Determine the force in the hydraulic actuator BE required to keep the lift in equilibrium. (Round the final answer to four decimal places. Include a minus sign if necessary.) The force in the hydraulic actuator BE required to keep the lift in equilibrium is lb.