A hollow shaft (k = 0.4) is subjected to a bending load of 500 N, and a torsion moment of 275000 N.mm as shown in the figure below. Design the outer and inner diameter of the shaft, oveild = 180 Mpa, F.S = 2 T= 275000 N.mm P= 500 N L=25 cm

A hollow shaft (k = 0.4) is subjected to a bending load of 500 N, and a torsion moment of 275000 N.mm as shown in the figure below. Design the outer and inner diameter of the shaft, oveild = 180 Mpa, F.S = 2 T= 275000 N.mm P= 500 N L=25 cm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.9P: A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same...

See similar textbooks

Related questions

Q: A cylindrical shaft made of steel of yield strength 700 MPa is subjected to static loads consisting…

A: Givenσy=700 MPaτ=σyF.S×0.58=7002.1×0.58=193 MPaM=10 kN=10000 NT=30 kN=30000 N

Q: 7. A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as…

Q: A wire of circular cross-section ofdiameter 1.0 mm is bent into a circular arc of radius 1.0 m by…

A: Given, Diameter of wire = d = 1 mm Circular arc radius = R = 1 m = 1000 mm Young's modulus = E = 100…

Q: A solid, circular bar ABC consists of two segments, as shown in the figure. One segment has a…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: Q.6. A circular bar AB with ends fixed against rotation has a hole extending for half of its length…

Q: 3.2-1 A copper rod of length L 18.0 in. is to be twisted by torques T(see figure) until the angle of…

Q: 3.4-3) A stepped shaft ABCD consisting of solid eircular segments is subjected to three torques, as…

Q: A borehole drilling machine with a vertical shaft of 60 mm diameter is 500 mm long and is supported…

A: For a rotating shaft if the rotational speed of the shaft is equal to the natural frequency of…

Q: A solid steel bar of circular cross section has diameter d =2.5 in., L = 60 in., and shear modulus…

Q: Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a…

A: Given: T =1200 NM G=78 GPa Allowable shear stress =40 MPa Allowable rate of twist 0.78/m TO…

Q: A hollow circular section shaft 2.5 m long is firmly supported at each end and has an inside…

Q: A section is under the effect of M (kNm) bending moment which makes 6° with the positive +z axis as…

Q: A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown…

Q: A stepped shaft ABCO consisting of solid circular segments is sublected to three torques, as shown…

Q: Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the…

A: Given The radius of steel wrench is r=0.4 cm. The length of steel wrench is l=0.200 m. The…

Q: (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and…

A: Given data Outer Diameter of Tubular shaft = Do = 50 mm = 0.05 mInner Diameter of Tubular Shaft = Di…

Q: A copper tube with circular cross section has length L 5 1.25 m, thickness t 5 2 mm, and shear…

A: Given: L = 1.25 m t = 2 mm T = 25 MPa G = 45 GPa Now, Using torsion equation,

Q: A shaft with a length of 2 m has the cross section shown in Figure 1, where a = 4 cm and t = 4 mm.…

A: Torque Torque is a rotational equivalent of linear force. Torsion Torsion is the twisting of an…

Q: A hollow aluminum tube used in a roof structure has an outside diameter of 104 mm and an inside…

A: Given data: τ=48 MPaD=104 mmd=82 mmL=2.75 mG=28 GPa Need to determine the angle of twist.

Q: A solid shaft BC is fixed at the B end and subjected to torque T at the C end, as shown below. The…

Q: A prismatic bar of length L with a solid circular cross section of diameter d is loaded by a…

Q: PROBLEM 3. The beam shown in the figure is made of steel with oạ-300 MPa. Determine the maximum…

Q: 6.8-3 An IPN 240 steel beam has the cross section shown in the figure. The dimensions are b = 106…

A: Symmetric section τmax is at neutral axis-

Q: 4. M 5 in. |t = 0.25 in. 3.25 in. a) The rectangular tube shown in the figure is obtained from an…

Q: A shaft supported on bearings 200mm apart transmits 187 kW at 200rpm. The maximum bending moment is…

Q: A prismatic bar AB of length L and solidcircular cross section (diameter d) is loaded by…

A: Given Diameter = d Length = L Find Maximum shear stress Angle of twist

Q: A circular solid shaft, with an radius of 20 mm and a length of 5 m and thin bearings at both ends,…

A: step 1

Q: 40 N.m Da 0.5 m 280 N.m 150 N.m 2 0.3 m 0.4 m

Q: 1. The nonprismatic cantilever circular bar has an internal cylindrical hole from 0 to x, so that…

A: Given data J1=78IpJ2=Ip (a) ∑Mx=0,Find reaction momentR1+T+T2=0R1+T+T2=0R1=-32T

Q: The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner…

Q: A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured. The…

A: given torsional torque T=1200 N.mshear stress for shaft material τ= 40 MPalargest permissible unit…

Q: A stepped shaft ABC consisting of two solid circular segments is subjected to torques '1 and T,…

Q: A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has…

Q: A solid round bar. 25 mm in diameter. has a groove 2.5-mm deep with a 2.5-mm radius machined into it…

Q: The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and…

A: Given: The yield strength of material, Sy = 600 MPa The ultimate strength of the material, Su = 700…

Q: Question 3 - Torsion ( A composite shaft is shown in the figure below which is fixed against…

Q: The shaft in the figure is mounted with a gear wheel key. Shaft material 42CrMo4 The weight of the…

Q: A copper tube with circular cross section has length L = 1.55 m, thickness t = 2 mm, and shear…

Q: 3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has…

A: Given dataPower delivered the shaft P = 20kWShaft frequency f = 12Hz1) To determine maximum shear…

Q: Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is…

Q: A steel bar withstands simultaneously a 30 kN compressive force, a 5 kNm bending moment and a 1kNm…

Q: A simply supported beam AB = 11 m has a hollow rectangular cross-section with 14 cm as width, 29 cm…

Q: A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is…

Q: 6. A circular bar AB with ends fixed against rotation has a hole 25 in. 4 130 in ending for half of…

Q: M-2000 Ncm 500 Ncm M-800 Nem M300 Ncm M-400 Ncm A B- L-20cm M.

Q: A hollow circular tube having an inside diameter of 10.0 in. and a wall thickness of 1.0 in. (see…

A: Given Torque, T = 1200 kip-in Thickness, t = 1 in Inside Diameter, D = 10 in Outer diameter, d =…

Q: e following is TRUE for a hollow circular shaft subjected to a uniformly distributed in the elastic…

A: The maximum shear stress will occur at outer surface and is uniform along length. So option A is…

Q: The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and…

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

A hollow shaft (k = 0.4) is subjected to a bending load of 500 N,
and a torsion moment of 275000 N.mm as shown in the figure
below. Design the outer and inner diameter of the shaft, oveild =
180 Mpa, F.S = 2
T= 275000 N.mm | P= 500 N
L=25 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A long, thin-walled tapered tube AB with a circular cross section (see figure) is subjected to a torque T. The tube has length L and constant wall thickness t. The diameter to the median lines of the cross sections at the ends A and B are dAand dB, respectively. Derive the following formula for the angle of twist of the tube: Hint: If the angle of taper is small, you may obtain approximate results by applying the formulas for a thin-walled prismatic tube to a differential element of the tapered tube and then integrating along the axis of the tube.
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A stepped shaft ACE is held against rotation at ends A and B and subjected to a torque T0acting at section C(see figure). The two segments of the shaft (AC and CB) have diameters dAand dg, respectively, and polar moments of inertia IpAand IpBrespectively. The shaft has length L and segment AC has length a. For what ratio a/L will the maximum shear stresses be the same in both segments of the shaft? For what ratio a/L will the internal torques be the same in both segments of the shaft?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A statically indeterminate stepped shaft ACE is fixed at ends A and B and loaded by a torque TQat point C (see figure). The two segments of the bar are made of the same material, have lengths L4and LB, and have polar moments of inertia IAand Ipb. Determine the angle of rotation 4>of the cross section at Cby using strain energy. Hint: Use Eq, (3-55b) to determine the strain energy Urn terms of the angle d?. Then equate the strain energy to the work done by the torque to. Compare your result with Eq. (3-52) of Example 3-9.