A hanging plant with a mass of 10 kg hangs from three ropes as shown. Knowing that Y= 1.4 m and X = 4 m, determine the force in ropes AB, AC, and AD. Enter for force in AC below. Express your answer in N to the nearest 0.1 N.

A hanging plant with a mass of 10 kg hangs from three ropes as shown. Knowing that Y= 1.4 m and X = 4 m, determine the force in ropes AB, AC, and AD. Enter for force in AC below. Express your answer in N to the nearest 0.1 N.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.19P: The horizontal boom carries the weight W=108lb at A. The boom is supported by the cables AB and AC....

See similar textbooks

Related questions

Q: F= 250N 40 9 Black = 3,5m/52 M= friction Block m= 8kg coefficient btwn black and channel 250M force…

Q: Please write down Darcy’s law with pressure and potential form separately, explain the meaning of…

A: This law describe the fluid through the porous medium.French engineer Henri darcy governs the law…

Q: Force-couple systems: A couple is a pair of forces, equal in magnitude, oppositely directed (sum of…

Q: x bar and the shaded in following figure. Also determine inertia along x moment Q. Find of gi la the…

Q: In a dual combustion cycle the maximum combustion temperature is 2000degrees Celsius and maximum…

Q: QUESTION 26 A gate of a tank containing water and oil is kept in the closed position by applying a…

Q: A Scotch yoke is a mechanism that transforms the circular motion of a crank into the reciprocating…

Q: mercury Water flows at a flow rate of Q=5 lt/s from the system with diameters of d₁=60 mm and d₂=40…

A: This question is based on the concept of Bernoulli's equation. The assumptions are- Steady Flow: The…

Q: Problem 3. Outcome 5. Please show all work. Air at standard pressure but with T = 50°C flows through…

Q: 6.* Figure 6 shows two plates of thickness t = 6 mm and width (into the paper) 50 mm tha are joined…

A: please refer handwritten solution

Q: find its equation of motion to find y (1). Round up the answer to the second decimal place point.

Q: A sample of steam is at a pressure of 500 kPa (x=0.9) before entering a condenser then exiting it…

Q: Nominal or engineering strain in the rod

A: Given DataThe gauge length of the specimen The initial diameter d0 =0.5 inYield stress f…

Q: Calculate the reactions at the supports and obtain the shear force and bending moment diagrams for…

A: Given:To find:Reactions Shear force and Bending moment diagram

Q: C* W B A Y F₁ FM

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A: Pressure angle is 20 degreeNumber of teeth on pinion is 24Number of teeth on gear is 96Pinion…

Q: (b) Consider a sealed 20-cm-high electronic box in Figure 1 whose base dimensions are 50 cm x 50 cm…

A: Dimension of box=Height of box, H=20 cm=0.2 mPower dissipate, P=120 wOutersurface temperature,…

Q: A 2 B AB=20 cm AC=50 cm 3 12 = 0.01 kg.m² 13 = 0.457 kg. m² 14 = 0.01 kg.m² W₂ = 10 rad/sec CCW…

Q: Calculate -3 -6 . 10 ft L -3 ft a dx. a, ft/sec² 19 0 0 x, ft 5 7 10

A: Consider following acceleration vs displacement graph.We need to determine the total acceleration…

Q: ii) iii) For the construction of phase diagrams, instantaneous quench to a fixed temperature is…

A: This question is based on the concept of material science

Q: For the diagram below, derive for the angular displacements of the rotating discs. GJ₁ Li 05 (1) M1…

A: For solution refer below images.

Q: 1) Determine if pump pressure is sufficient to lift the weight L: 3 Li 1.4m C 4m 5 6kg oc Dynam 32sm…

Q: What are is the maintenance procedure and safety to follow on the tirfor machine?

A: The Tirfor machine, also referred to as a hand winch or a pulling hoist, is an adaptable device used…

Q: Refrigerant R134a enters an expansion valve at 800 kPa as a saturated liquid and exits at 100 kPa.…

A: Given:The initial pressure is .The final pressure is .The initial condition is saturated…

Q: The center of mass G of a high jumper follows the trajectory shown. Determine the component vo,…

Q: Determine the resultant force at support A. 2 2 Hint: A = √4² +4,²

Q: A shaft given in the figure has four masses of 200 kg, 300 kg, 400 kg and 200 kg, respectively. and…

A: Consider the balancing masses in plane L as and in plane R as .Represent the position of planes and…

Q: What are the fundamental principles of engineering metrology and how do they contribute to ensuring…

A: Engineering metrology is the study of measurement science and the application of that science to…

Q: Car A is traveling at a constant speed VA = 144 km/h at a location where the speed limit is 100…

A: The speed of car A, vA = 144 km/h = 40 m/sThe acceleration of car B, a = 5.8 m/s^2The speed of car…

Q: 1.5 m 1.0 m A B 3.3 m FIGURE P1.10 C 15 kN 12 kN

A: Considering that you want to know the forces in the members.Thus the reaction forces are as shown…

Q: b) To slow the boat very quickly a thrust reverser (or speed brake) is deployed (as shown in the…

A: Given data :-Velocity of V1=V2= VNozzle area (a) = a2Angle = 90°Find out :- Thrust force on the…

Q: A 2 4 M F B L₂ L Y C 4 Pipe ABC is supported by three smooth journal bearings, Find the reactions at…

A: Applied force F = 480 lbsApplied moment M = 180 lb-ftAngle of the applied force , θ = 45°Lengths: L1…

Q: (b) A transistor with a height of 0.4 cm and a diameter of 0.6 cm is mounted on a circuit board as…

A: Height, H = 0.4 cm or 0.004 mDiameter, D = 0.6 cm or 0.006 mAverage heat transfer coefficient, h =…

Q: A pump is tested in the laboratory and the following data were obtained. Determine the pump…

Q: iv. G(s) = 54 s²+12s+36 a) Find the location of the poles, natural frequency and damping ratio…

A: a) Poles: s=-6 (repeated pole) Natural Frequency: ω_n = 6 Damping ratio: ζ = 0.5b) Step response =…

Q: Consider the spring assemblage shown, using the direct stiffness method do the following: 1. Write…

A: Here are reaction forces at node-1 and node-4, is applied force at node-2, are nodal…

Q: A steel pipe with heat transfer coefficient of 42 W/mK contains flowing water. The outer diameter of…

A: A steel pipeheat transfer coefficient K = 42 W/mKOuter diameter of the pipe Do = 90 mmFor r1Di =…

Q: A trough whose cross section is an equilateral triangle with side a = 3 m long is filled with water.…

A: Given:Triangle is givenSide, a= 3m To find:Force due to the water pressure on the one end of the…

Q: 2. The disk is originally rotating at w=8 rad/s. If it is subjected to a constant angular…

A: Initial angular speed of disk is 8 rad/s Angular acceleration is 6 rad/s^2 Required: Velocity,…

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

Q: Show and explain all the equations and constants required to calculate what the exit temperature…

A: Step 1: Calculate the average heat transfer coefficient "U" using the following equation:U =…

Q: Water enclosed in a rigid tank is heated from 120°C to 250°C. The pressure is high enough that the…

A: please refer handwritten solution

Q: The guide with the vertical slot is given a horizontal oscillatory motion according to x = 5.1 sin…

A: Given:To find:Position, time and max velocity

Q: Steam at 100 kPa and 200C is heated to 500C.What is the change in enthalpy?

Q: The prototype water pump is required to generate a pressure rise of 750 kPa with the mass flux of…

A: For Prototype (Pressure rise)p = 750 kPa(Mass flux)p = 950 kg/sScale (Lr) = 1:5.5Water is used in…

Q: 4: A rod of length L. coincides with the interval [0, L] on the x-axis. Let u(x, t) be the…

Q: A particle travels along a straight line with a velocity of v = (20 0.05s²) m/s, where s is in…

Q: We assume that air at 40°C passes over a 1.5 m long and 50 cm wide plate with a velocity of 3 m/s,…

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500-lb load.…

Q: The beam loading is shown in Figure Q4a, and the cross section in Figure Q4b when cut at A-A. The…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

A hanging plant with a mass of 10 kg hangs from three ropes as shown.
Knowing that Y= 1.4 m and X = 4 m, determine the force in ropes AB, AC,
and AD. Enter for force in AC below. Express your answer in N to the
nearest 0.1 N.
4m
B
3 m
www
Your written solution must show an appropriate FBD and calculations to
determine the force in all three ropes (AB, AC, and AD).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given values and free body diagram

VIEW

Step 2: Unit vectors

VIEW

Step 3: Equilibrium at point A

VIEW

Step 4: Value of forces

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Cable ABC of length 5 m supports the force W at B. Determine (a) the angles 1 and 2; and (b) the force in each cable segment in terms of W.
The horizontal boom carries the weight W=108lb at A. The boom is supported by the cables AB and AC. The tensions in the cables are TAB=120lb and TAC=160lb. Determine the single force R that is equivalent to three forces acting on the boom at A.
The frame shown supports a crate that weighs W = 250 lb. Knowing that L = 1.1 ft, determine the internal forces (N, V, M) at points E and F. Enter the internal normal force at F below. Express your answer in lb to the nearest whole lb. Remember the sign convention for internal forces, and use the correct sign. 1.5 ft 1.5 ft L L 4 ft B E 0.4 ft N
1) The OABCDE plate which has a weight of 300 N is hanged with three cables as shown. Find the cable forces. 50 cm 50 cm 50 cm 50 cm
200 400 B 200 N m E D 200 F Dimensions in mm Determine the magnitude of the force (in N) of the x-component of the internal pin at D.
2. Question : For the given three bar support system, determine the internal forces at the point p, in bar ABCD and at the point p2 in bar BEF. F 400 N 4 m 1000 N E 2.5 m P2 4 m В P1 2 m 3 m 3 m 2 m
Determine the magnitude of the resultant force at A. A Fg = 840 N 6 m Fc = 420 N %3D 3 m B 2 m 3 m 2 m Select one: O a. 4.3 kN b. 1.2 kN O c. 3.5 kN O d. 2.4 kN Clear my choice
The guy cables AB and AC are attached to the top of the transmission tower. The tension in cable AB is 8 kN. Determine the required tension T in cable AC such that the net effect of the two cable tensions is a downward force at point A. Determine the magnitude R of this downward force: asonot ow esil nda toWniloni sda ban Tlo obutin Ianierotob M adi ovods 30 m 20 m B. 40 m 50 m C. XX XIXI X
2. The homogeneous bar AB weighs 25 lb. Determine the forces acting on the bar at A and B. Neglect friction. 60° A
30 cm 18 cm Hom Scm Hom Sum 2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force developed at A if a force P = 100 N is applied perpendicular to the handle when the handle is at the position indicated.
The cable BC carries a tension of 750 N. Write the force in the cable as a vecto 12m- C 0.7 m 1.6 m.
Determinethe magnitude (lb) of the horizontal component of force at point C if P = 150.5 lb, x = 13.6 in, y = 6.8 in, and z = 8.3 in.