A gas expands from pressure P1 topressure P2 (P2 =), If the process of10.expansion is isothermal then thevolume at the end of process is 0.55m³.If the process of expansion is adiabatic,the volume at the end of expansion willbe closer to (Y =1.4)

Given, Relation between intial and final pressure : P2 = P110 Ratio of specific heats = γ = 1.4…

Answered: A gas expands from pressure P1 to P1…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An automobile tire contains a certain volume of air at 205 kPa g and 20 0 C. The barometricpressure is 100 kPa a . If due to running conditions the temperature of the air in the tire risesto 70 0 C, what will be the gage pressure? Assume that the air is an ideal gas and that thetire does not stretch.
3 A fluid of density 1200 kg/m° at 1 atm pressure is compressed to 101 atm pressure isothermally. If the isothermal compression is 4.8, 105 atm. -1 the 3. increase in density in kg/m of fluid is
Q3/A/ cylinder vessel of carbon monoxide (3.0 kg ) at -30°C with length 1.5 m and inner diameter 0.3 m , find pressure in bar used I- the van der Waals equation, 2- ideal gas equation
50 ton Water 4. The figure shows two cylinders of diameter D and 2D, connected to each other and containing an incompressible fluid. The two cylinders are filled with leak-proof pistons of weight W1 and W2 as shown. The releationship between WI and W2 is a) W2 = W1 b) W2 = 0.5 W1 c) W2 = 5 W1 d) W2 = 0.4 WI 20 5. A flat plate is sliding at aconstant velocity of 5 m's on a large horizontal table. A thin layer of oil ( of absolute viscosity = 0.4 N.s/m?) separates the plate from the table. To limit the shear stress in the oil layer to 1 kpa, the thickness of the oil film (mm) should be most nearly to ... a) 0.2 c) 1.6 b) 20 d) 1.85
50 ton Water 4. The figure shows two cylinders of diameter D and 2D, connected to each other and containing an incompressible fluid. The two cylinders are filled with leak-proof pistons of weight W1 and W2 as shown. The releationship between W1 and W2 is. a) W2 W1 b) W2 = 0.5 WI c) W2 = 5 W1 d) W2 = 0.4 W1
Hey steel tank with an interior volume of 30 m^3 contains an ideal gas of 300 K and 1E5 Pa of pressure (atmospheric pressure) if tank is sealed and the gas is heated to 450 K what will the new pressure be
A spherical research balloon is filled with 420 m3 of atmospheric air at atemperature of 10 oC. If the air inside the balloon is heated to 80 oC accordingto PVn =C, where n = 0. What will be the final diameter of the balloon?
the specific heat capacity of the system during a certain process is given by Cn(0.4+0.004T) kJ/kg deg. celcius. if the mass of the gas is 6kg and its temperature changes from 25 def. celcius to 125 def. celcius find the mean specific heat of the gas
2. A vertical cylindrical tank is filled to the top with water at a temperature of 20°C. The diameter of the tank is 12m and depth of 4m. If the water is heated to 50°C, how much water will spill over in m? 3 A quart of SAE 30 oil at 6goE weighse about 1 85lh. Calculate the oil's
One closed tough tank inside the package The pressure inside the tank is 800 kPa if the mass of water in liquid form is 0.05 kg and the mass of water in gas form is 1.95 kg. The whole body is vaporized. Find this new pressure.
In a reciprocating air compressor, high pressure air in the cylinder pushes the piston against the external load and expand to a lower pressure. In a test the following measurements were noted:Internal energy of air before expansion = 27 kJInternal energy of air after expansion = 8 kJHeat entering the cylinder during the process = 2 kJSHOW THE DIAGRAM USING THE GIVEN PROVIDED
A giass contai ner with volume of 4 liters filled with water, then heated until the in crease in temperature is 20 C Some water Spilled Given the coefficient of linear expansion for glass = 9 X10-6oc-!. and coefficient %3D Of volume expansion of water = 2.1 X10-°C-. Determine the volume of spilled water ?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A gas expands from pressure P1 to P1 10. pressure P, (P, =5). If the process of expansion is isothermal then the volume at the end of process is 0.55m3. If the process of expansion is adiabatic, the volume at the end of expansion will be closer to (y =1.4)