Please solve all showing all the steps in detailY = 4X= 9 A Full Wave rectifier is needed to produce a peak output voltage of Vp = (12+)V, deliver apeak current I = 120mA to the load. The ripple voltage V₁ must not be more 2.5% of VM.a. What is the value of input maximum, VM?b. What is the value of load resistance, R₁, and capacitance, C?c. Sketch the circuit with appropriate values.Frequency f = 50 Hz. Consider the diode(s) as Si/Ge diode.

a. The peak output voltage of the full wave rectifier is, VP=12+Y2 VY=4VP=12+42 VVP=14 V The peak…

A Full Wave rectifier is needed to produce a peak output voltage of Vp = (12+)V, deliver a peak current I₁ = 120mA to the load. The ripple voltage V, must not be more 2.5% of VM. a. What is the value of input maximum, VM? b. What is the value of load resistance, R₁, and capacitance, C? c. Sketch the circuit with appropriate values.. Frequency f = 50 Hz. Consider the diode(s) as Si/Ge diode.

A Full Wave rectifier is needed to produce a peak output voltage of Vp = (12+)V, deliver a peak current I₁ = 120mA to the load. The ripple voltage V, must not be more 2.5% of VM. a. What is the value of input maximum, VM? b. What is the value of load resistance, R₁, and capacitance, C? c. Sketch the circuit with appropriate values.. Frequency f = 50 Hz. Consider the diode(s) as Si/Ge diode.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL