A concentrated load of P = 29 KN is applied to the upper end of a 2-m-long pipe as shown. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum vertical shear stress in the pipe. B 3.24 MPa O 2.41 MPa O 2.80 MPa O 3.57 MPa O 3.90 MPa L O

A concentrated load of P = 29 KN is applied to the upper end of a 2-m-long pipe as shown. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum vertical shear stress in the pipe. B 3.24 MPa O 2.41 MPa O 2.80 MPa O 3.57 MPa O 3.90 MPa L O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2:The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in the shaft and sketch the shear-stress distribution along a radial line of the shaft where the shear stress is maximum. Set T=2000 N - m. %3D D. 300 N-m 600 N-m 900 N-m
1. The rectangular tube has the dimensions as shown. It is extruded from aluminum alloy 2014-T6. Determine the local compressive buckling stress. kh=5.2 .04 T b 1.0 .04 h 2.0
Question 8 20 Points Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that the applied load P = 70 kN is distributed equally among the three rivets. Determine the tensile stress (MPa) in the plate at the critical section. ... P 000- P
The driveshaft of an automobile is being designed to transmit 238 hp at 3790 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 5700 psi. Answer: d = i in.
Solve the following problems on separate sheets of paper. Show complete solutions and appropriate free-body diagrams. Problem 1: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress developed in the shaft. The shaft has an outer diameter of 90 mm, and the thickness of the wall of the hollow segment is 15 mm. 4 kN-m 2 kN-m Problem 2: A steel tube having an outer diameter of 2.5 in. is used to transmit 10 hp when turning at 30 rev/min. Determine the inner diameter d of the tube to the nearest 1/8 in. if the allowable shear stress is tatow = 12 ksi. 2.5 in. CTY SAFE
120 mm a 60° A torque T=30 kNm is applied to the hollow shaft shown that has a uniform 10- mm wall thickness. What is the shear stress at point b? Express your answer in MPa and round it to the nearest integer if necessary.
What are appropriate relations established from the calculation of maximum shear stress in a thin circular tube? 4 (b) t = (a) Tmax Tavg 3 'avg max 3 4 S Rỉ + R2R1+ R3 (c) Tmax when (R, = = 2avg - R.) (d) Tmax 3 A Rỉ + R? Here, (R, > R1) and S is shear force at the cross sectional and A is cross sectional area.
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
2 Points Question 14 of 15 The cross-sectional area of a column is in the shape of two concentric circles whose outer diameter is 200 mm. If it is to be subjected to a force of 75 kN, find the thickness of the wall if the ultimate stress capacity is 32 MPa. Use FS = 3.2 Select the correct response: 12.57 mm 17.75 mm 12.75 mm 15.75 mm rs ion
3. A compound shaft consists of two pipe segments has the following properties: SET Segment Segment Segment Segment Torque TB Torque TC 2 wall thickness 1 wall 2 thickness Outside 1 outside diameter diameter A 400 mm. 12.5 mm 320 mm 10 mm 81.35 kN.m 28 kN.m Determine the magnitude of the maximum shear stress in segment 2. (1) TC B
2. If we have the inside shearing stress (point A), T= 50 N/mm'. Calculate the outside shearing stress (point B) i.e. T max- B 125 mm
Q2: The column is subjected to an axial force of 8 kN, which is applied through the centroid of the cross-sectional area. Determine the average normal stress acting at section a-a. Show this distribution of stress acting over the area's cross section. 8 kN 75 mm 75 mm 10 mm 10 mm 70 mm 10 mm 70 mm a a