A concentrated load of P = 24 kN is applied to the upper end of a pipe with length L=7 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B P O 160.7 MPa O 190.2 MPa O 91.0 MPa O 150.2 MPa O 177.4 MPa O

A concentrated load of P = 24 kN is applied to the upper end of a pipe with length L=7 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B P O 160.7 MPa O 190.2 MPa O 91.0 MPa O 150.2 MPa O 177.4 MPa O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1a) Figure Q1a shows two tubes made of the same material which are riveted together by 50 rivets of 5mm diameter pitched uniformly. The left tube is fixed at section A and the right tube is subjected to an axial tensile force of 20kN. The thickness of both tubes is 5mm. The inner diameter of the right tube is 180mm. Take E-100GPa. Determine, the normal stress in each tube and shear stress in each rivet. the axial tip displacement at section B. Assume the rivets are rigid. the total strain energy stored. () i) iii) Figure Q1a 200mm 1m. Rivet 190mm 1m. B 180mm F=20KN
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 442 mm². Determine the axial stress in each bar. B 2 m O 1 m 5Q KN 1 m O E 1 m 8T KN 1 m LL
The driveshaft of an automobile is being designed to transmit 238 hp at 3790 rpm. Determine the minimum diameter d required for a solid steel shaft if the allowable shear stress in the shaft is not to exceed 5700 psi. Answer: d = i in.
Problem 6.2: The aluminum rod ABC (E=10.1x10° psi) (Figure 6.19), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E=29x10° psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation 28 kips 25 kips A D 12 in. -1.5 in. is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ksi. B - 2.25 in. 18 in. E Figure 6.19
Question 8 20 Points Two plates each 25 mm thick and 130 mm wide are fastened by three 20 mm diameter rivets. Assume that the applied load P = 70 kN is distributed equally among the three rivets. Determine the tensile stress (MPa) in the plate at the critical section. ... P 000- P
The three suspender bars in figure shown are made of A-36 (E = 200 GPa) steel and have equal cross-sectional areas of 450 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. . A В 2.5 m 50 kN D E F 1 m 2.5 m 1.5 m
A 2 m long shaft is transmitting 90 kW at 150 RPM. The allowable shear stress in the material is 60 MPa. If the shaft is not allowed to twist more than 1°, then the diameter of the shaft required will be (Take G = 85 GPa)
2.50 Before the 400-kN load is applied, the rigid platform rests on two steel bars, each of cross-sectional area 1400 mm², as shown in the figure. The cross-sectional area of the aluminum bar is 2800 mm². Compute the stress in the aluminum bar after the 400-kN load is applied. Use E = 200 GPa for steel and E = 70 GPa for alumi- num. Neglect the weight of the platform. | 400 kN 0.1 mm -b b - A B C G -1.2b- FIG. P2.49 FIG. P2.50 Steel Aluminum Steel 250 mm-
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the permissible flexure stress of 10MPa. B. Determine the maximum value of w without exceeding the permissible shear stress of 1.2MPa. C. Determine the maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E = 200, 000MPa and = 11.7 um Neglect bending of the beam. m°C A=640mm2 A=320mm2 A 1.2 m 0.8 m 1.2m 54KN What is the stress of rod C if there is no change in temperature in MPa?
Problem 3 A block with a weight W hangs from a pin at A. Support bars AB and AC are pinned to the support at B and C. Bar AB has a cross-sectional area of 750mm2 and 500mm2 for bar AC. Neglecting the weights of the bars, determine the maximum safe value of W if the stress in bar AB is limited to 100MPa and that in bar AC to 125MPa. 40 A
2.pdf A solid aluminum shaft (2 in) in diameter is subjected to two torques as shown in Figure below. Determine the maximum shearing stress in each segment and the angle of rotation of the free end. Use G = 4 x 106 ps 200 Ibft 800 bft 2 ft 3 ft - Determine the maximum stress in the member CD if you know that the distributed load W = 40 kN/m, the diameter of member CD is 45 mm and E=200 GPa.