A CCA chemistry student needed to determine the % hexane in an unknown sample. The student determined density values for a set of standards and then measured the density value for the unknown sample. Using the experimental data from the student shown below, plot a line and determine % hexane for the unknown sample. You must also follow all the instructions given throughout this handout. % hexane 100.0 80.0 60.0 40.0 20.0 unknown Density (g/mL) 0.642 0.684 0.724 0.766 0.806 0.699

A CCA chemistry student needed to determine the % hexane in an unknown sample. The student determined density values for a set of standards and then measured the density value for the unknown sample. Using the experimental data from the student shown below, plot a line and determine % hexane for the unknown sample. You must also follow all the instructions given throughout this handout. % hexane 100.0 80.0 60.0 40.0 20.0 unknown Density (g/mL) 0.642 0.684 0.724 0.766 0.806 0.699

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter1: Matter, Measurements, And Calculations

Section: Chapter Questions

Problem 1.82E

See similar textbooks

Similar questions

O MEASUREMENT AND MATTER W start Page Predicting the units of the solution to a basic quantitative... A student sets up the following equation to solve a problem in solution stoichiometry. (The ? stands for a number the student is going to calculate.) Enter the units of the student's answer. 1 mL 0.59 mL - 3 10 x10 108.39 mol II
How will each of the following experimental errors influence the results of your calculated densities you reported? State whether the error will tend to make your density results too large, too small or unchanged. Explain why this would occur by identifying which measurements would be affected (high or low) and how this would affect the calculated density. Use the followingIn method 2, the metal cylinder you used had a number of air bubbles on its when immersed in the water
Peak A has a height of 62 mm and a width at half height of 12 while peak B has a height of 84 and a width at half height of 6. What is the percent composition of peak B? Please give your answer as a whole number and do not include "%".
Atomic masses are measured in atomic mass units (amu). The amu, (1.66)(10-27) kilogram, is defined as 1/12 the mass of a common carbon atom. Find the mass of a carbon atom in kilograms. Express the result in scientific notation.
Part 1) what is average density of water samples. ( 1 g/ml) Part 2) what is percent error.
At 20oC 25.0 ml of concentrated nitric acid solution was found to have a mass of 32.503 g. What is the calculated density of this solution at 20oC? Show your calculation set-up and result using correct significant figures and proper units
0.45 mol ethanol V= ? L Express your answer using two significant figures.
1.092 x 101g% = cg
1) State your interpretation of the meaning of the slope for the first graph you prepared of Volume of Steel Nuts (mL) versus Number of Steel Nuts. Hint: Understanding the meaning of a slope involves several factors: the units which are a ratio of the y axis units over the x axis units, the interpretation of the slope as “number of the y axis units for every one of the x axis units” and the concept that constructing the best line or curve that follows the trend in the data is a sort of averaging of the random error throughout the data.
Perform Dixon's Q-test for the following data points. Make a conclusion to reject or retain the outlier. Show your calculation. Given: Mass of 1 -peso coin collected from Experiment 1
4. When you get your 5th correct answer, you will get a certificate that you can share with your teacher letting your teacher know how you did. Please provide a screenshot of your certificate showing you got this completed. DATA Part B: Measuring the Mass of Materials Top Loading Balance Mass Empty Beaker (g) Mass of Beaker + Paper Clips (g) Mass of Paper Clips (g) Analytical Balance Mass of Empty Beaker (g) Mass of Beaker + Paper Clips (g) Mass of Paper Clips (g) DATA ANALYSIS: 1. Show your calculation for the mass of paper clips using the top-loading and analytical balances. 2. Which of the balances, top-loading or analytical, has the most uncertainty per measurement? Explain. Page 10 of 14
answer then one of those cheap samples crept into ou stock of metal samples and you "unknown metal”. Note: volume measurements are not very exact. If your density determination is off by 0.1 or 0.2 from the known value, that's probably good enough for an identity. Metal Platinum Gold Tantalum Silver a) You weight your sample and determine it weighs 71.8 grams. You put the sample into 15.6 mL of water and the total volume rises to 22.4 ml. What metal do you have? Density (g/ml) 21.45 19.32 16.65 10.50 Metal Palladium Rhodium Plutonium Uranium Density (g/ml) 12.02 12.41 19.84 18.95 Metal Polonium Niobium Tungsten Gallium Density (g/ml) 9.3 8.57 19.35 5.91 b) You weight your sample and determine it weighs 56.3 grams. You put the sample into 28.9 mL of water and the total volume rises to 32.9 ml. What metal do you have? c) You weight your sample and determine it weighs 105.3 grams. You put the sample into 31.2 mL of water and the total volume rises to 39.6 ml. What metal do you have? d)…