A cast iron pulley transmits 20 kW at 300 r.p.m. The diameter of the pulley is 550 mm and has four straight arms of elliptical cross-section in which the major axis is twice the minor axis. Find the dimensions of the arm, if the allowable bending stress is 15 MPa. [Ans. 60 mm; 30 mm]

A cast iron pulley transmits 20 kW at 300 r.p.m. The diameter of the pulley is 550 mm and has four straight arms of elliptical cross-section in which the major axis is twice the minor axis. Find the dimensions of the arm, if the allowable bending stress is 15 MPa. [Ans. 60 mm; 30 mm]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.3.8P: At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure....

See similar textbooks

Related questions

Q: Beams, Shear Force and Bending Moment in Beams Problem#3: HOMEWORK Draw Shear Force and Moment…

A: The reaction force acting at A and B due to the symmetry is RA=RB=100+1002=100 lbs For this question…

Q: What is the minimum steel shear area (Av in sq.mm.) of a beam 300mm wide if fc'=21MPa and fy=340?…

A: Given, Width of the stirrups,w=300mmSpacing of stirrups,s=220mmfc'=21MPafy=340MPaTo…

Q: Consider the beam shown in (Figure 1). Suppose that the distributed load intensities w1 = 60 lb/ft…

A: The forces acting on the beam is shown below,

Q: Consider the beam shown in (Figure 1). Suppose that w1 = 460 N/m , w2 = 230 N/m . Follow the sign…

Q: Problem #5: For the 2D beam below, with F shear and bending moment diagrams. Report your answer in…

A: Given data: The force Fo is 15 kips. The force wo is 2.5 kip/ft. The moment Mo is 7 kip-ft. Draw…

Q: What is the internal normal force, shear force, and bending moment at point C, if F=40kN?

A: Given The value of force is F=40 kN. The load on beam consist of uniform distributed, uniform…

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L= 800 mm.…

A: Answer: The largest moment M that can be applied to the beam is 494.6 N•m.

Q: Problem #5: For the 2D beam below, with F, = 15 kips, M, =7 kip-ft, and shear and bending moment…

Q: Draw shear force and Bending moment Diagram 8 kip 3 kip/ft 3 ft 5 ft 8 ft

Q: igid support geomet in the figure and parameter table. Find the equations for the shear and moment…

A: Given: The length of AB, L1 = 4 m The length of BC, L2 = 4 m The length of CD, L3 = 3 m The moment…

Q: (i) Power transmission =60 kW, (ii) Shaft speed = 160 rpm, (iii)The angle of twist / m length = 1.1º…

Q: Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller…

Q: 7.0 kN/m 4m 16 m

A: given; ⇒reaction force at A=RA⇒reaction force at B=RB⇒load intensity (w)=7KN/m⇒AC=16m⇒BC=4m

Q: axial force, shear force and bending moment at a section

A: EXPLANATION-

Q: 8KN 2KN am 3m

A: given; w=2kN/m

Q: The internal shear force Vat a certain section of a steel beam is 80 kN, and the moment of inertia…

Q: Write equations for the shearing force and bending moment peam Plot the shear and moment diagram 200…

A: Given overhanging beam as shown below

Q: Draw the free-body diagram for the portion of machine structure shown in Figure 1. Determine the…

Q: The figure below shows a hollow circular beam with an outside diameter of 100 mm and a wall…

A: NOTE: According to Bartleyby's policy we shall answer only three sub-parts of a question so kindly…

Q: 16 kN | 4 kN/m 20 kN 2 kN/m A D - 4 m →- 8 m 8 m A. What is the value of shear at 2m from A? B. What…

Q: 1. A beam of length L is simply supported shown as follows. A concentrated force F is applied at…

Q: A horizontal beam under bending has a maximum bending stress of 100 MpA

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm.…

Q: aw the Normal Force Diagram. (b) Draw the shear force diagram. (c) Draw the bending moment…

Q: X= Your Registration No Ib/ft C: 7 ft 4 ft R2 R Fig 1.1

A: Given: Length of beam AC (l)=11 ft . Uniform varying load (w) at section AB =130 lb/ft .…

Q: 7.5 (A/B). Fig. 7.18 shows the cross-section of a beam which carries a shear force of 20 kN. Plot a…

Q: QS\ Draw shear force and bending moment diagram for the beam shown below 10kN/m 4m 3m

A: Draw the schematic diagram of the beam.

Q: 5. A mild steel shaft is subjected to a bending moment M = 400N.m and torque T = 300N.m . The…

A: Write the given data:

Q: 25 K 15 K 6ft 4 ft 3.0 K/ft 4 Use the free-body diagram pproach shown in Sections 5-3troush 5-5 o…

A: following is the answer to the above question-

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm.…

A: Find the largest moment that can be required.

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 600 mm.…

Q: 30 m 100 m 12mm 30 Omw os os stress in S teel bereling IF the max is 24 MPa Fined Moment the bending…

A: Stress When body is subjected to force then body will deform and body will resist the deformation…

Q: An electrical worker stands in the bucket that hangs from a pin at end D of the boom of the cherry…

A: The weight of worker and bucket together is 300lb Therefore the Free body diagram is

Q: 25. A fiberglass pipe is lifted by a sling, as shown in the figure. The outer diameter of the pipe…

A: Given data as per questionLength of pipe =10 ms=4 md2=100 mmd1=100−12=88 mmweight density =1500…

Q: For a loaded cantilever beam of uniform cross section, the bending moment along the length is M(x) =…

A: Given data: - The equation of the bending moment is Mx = 5x2 + 10x. The distance where the…

Q: Given the beam shown below (E=200GPA, I=180x106 mm4, 80mmx300mm), do the following: a. Draw the…

Q: - A circular shaft is subjected to a torque 'T and a bending moment M. The ratio of maximum shear…

A: Find the ratio of maximum shear stress to maximum bending stress.

Q: For the beam cross section below, a vertical shear force Sz of 2,250 N is applied through the shear…

A: Consider the diagram shown below for the given cross-section of the beam. The value of the moment…

Q: The shaft in Figure B1 is subjected to the concentrated forces shown. T sleeve bearings at A and B…

Q: Ql: An I-section shown in Fig. is simply supported over a span of 15 m. If the maximum permissible…

Q: A hollow circular shaft has an external diameter of 120 mm and the internal diameter is…

A: Given Data External radius, R=60 mm Internal radius, r=3/4(60 mm)=45 mm SHear stress, 36MPa G=85 MPa…

Q: A windmill turns a series of slender rods fixed about one end (see formula below). They are…

Q: Find Shear Force Equation. Find Bending Moment Equation. F=1.7 kN W=11.1 kN/m

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm.…

A: Given data L = 620 mm b1 = 39 mmd1 = 82 mmb2 = 23 mmd2 = 23 mma = 8 mmAllowable tensile bending…

Q: Example 5: Draw the shear force and bending moment diagrams for the simply supported beam as shown…

Q: Problem: 1 +12 For the given compound curve (see figure): a. Determine R1 and R2. b. Determine T,…

A: Since we only answer upto 3 subparts,we will answer the first three. Please resubmit the question…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A cast iron pulley transmits 20 kW at 300 1.p.m. The diameter of the pulley is 550 mm and has four
straight arms of elliptical cross-section in which the major axis is twice the minor axis. Find the
dimensions of the arm, if the allowable bending stress is 15 MPa.
[Ans. 60 mm; 30 mm]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A cantilever beam(Z, = 6 ft) with a rectangular cross section (/> = 3.5 in., h = 12 in.) supports an upward load P = 35 kips at its free end. (a) Find the state of stress ((7T, o^., and r in ksi) on a plane-stress element at L/2 that is i/ = 8 in. up from the bottom of the beam. Find the principal normal stresses and maximum shear stress. Show these stresses on sketches of properly oriented elements. (b) Repeat part (a) if an axial compressive centroidal load N = 40 kips is added at B
1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20 mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa. [Ans. 152 mm] 2. A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is connected to the shaft by means of a key, find the dimensions of the key so that the stress in the key is not to exceed 50 MPa and length of the key is 4 times the width. [Ans. / 126 mm] 3. A steel shaft has a diameter of 25 mm. The shaft rotates at a speed of 600 r.p.m. and transmits 30 kW through a gear. The tensile and yield strength of the material of shaft are 650 MPa and 353 MPa respectively. Taking a factor of safety 3, select a suitable key for the gear. Assume that the key and shaft are made of the same material. [Ans./= 102 mm]
the centre and it weighs 1 kN. Find the diameter of the shaft, if the permissible bending stress fo shaft material is 40 MPa. [Ans. 28.3 MPa (tensile); 17.7 MPa (compressive) 8. A shaft is supported in bearings, the distance between their centres being 1 metre. It carries a pulley in [Ans. 40 mm] A punch press, used for stamping sheet metal, has a punching capacity of 50 kN. The section oc.u frame is as shown in Fig. 5.35. Find the resultant stress at the inner and outer fibre of the section 9. 800 R 100 65 200 8 X= 100 116 300 A 90 kN 90 Section at X-X 25 1)
A shaft is transmitting 100 kW at 180 r.p.m. If the allowable stress in the material is 60 MPa, find the suitable diameter for the shaft. The shaft is not to twist more than 1° in a length of 3 metres. Take C= 80 GPa. [Ans. 105 mm]
A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. [Ans. 100 mm ; 50 mm]
Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the appropriate reduced shear stress equation. Assume Vmax = 12kN. Find the max shear stress in a W12x50 cross-section using the appropriate estimated shear stress equation. Assume Vmax = 236kips. Find the max shear stress in bending in the cross section below if Vmax = 10 kips. 10" Flange 2" Web 2" 8" Flange 2" 10" • Identify where in the cross section the max shear will occur. • Determine the thickness of the cross-section at the location you wish to find shear stress. • Calculate the Ix for the shape (assume bending in the x with most basic beams). • Calculate Q by dividing the section into two pieces at the point you want shear stress. Select one of the pieces (either will work), I picked the top piece. • Use the Shear Stress equation to determine the requested stress. • Compare you answer: Max shear stress = at the center of the cross section.
A shaft is required to transmit 1 MW power at 240 r.p.m. The shaft must not twist more than 1 degree on a length of 15 diameters. If the modulus of rigidity for material of the shaft is 80 GPa, find the MPa] diameter of the shaft and shear stress induced.
A uniform wind load of q = 0.2 kN/m? acts on the billboard with dimensions of b = 1.5 m and a = 1 m. The allowable normal stress is oalow = 140 MPa, c = 0.5 m for the circular cross section panel pole. Draw the shear force, bending moment and torsional moment diagrams for the panel pole. a) Calculate the cross-section diameter d, using the maximum shear stress (Tresca) criterion. b) Calculate the cross-section diameter d, using the maximum distortional energy (von Mises) criterion. SOLUTION kesit
2. A pipe of length L is lifted by a sling, as shown in the figure. The outer diameter of the pipe is 150 mm, its wall thickness is 6 mm, and its weight density is 14.7 kN/m³. The length of the pipe is L= 12 m and the distance between the lifting points is s = 4 m. [Ignore axial forces]. a. Derive expressions for the shear force and bending moment along the pipe. b. Determine the maximum bending moment and the location(s) where this occurs. c. Determine the maximum bending stress in the pipe due to its own weight.
the same magnitude of stress in compression. For points not on a surface of the beam, we can use Omax /c = -o/y Part A - Moment Required to Produce a Given Stress to rewrite the flexure formula in the more general form The cross-section of a wooden, built-up beam is shown below. The dimensions are L = 220 mm and w = 40 mm. Му (Figure 1) Determine the magnitude of the moment M that must be applied to the beam to create a compressive stress of op = 30 MPa at point D. Also calculate the maximum stress developed in the beam. The moment M is applied in the vertical plane about the geometric center of the beam. Figure Express your answers, separated by a comma, to three significant figures. > View Available Hint(s) 'D Vo AEd vec ? kN-m, MPа M =. Omax= Submit