A cantilever beam 10 ft long is subjected to a uniformly distributed load of 1500 lb per ft. of length. The allowable working stress in either tension or compression is 20,000 psi. If the cross section is to be rectangular. Determine the height if the height is to be twice as great as the width. a. 4.62 inch b. 9.24 inch c. 4.06 inch d. 8.12 inch

A cantilever beam 10 ft long is subjected to a uniformly distributed load of 1500 lb per ft. of length. The allowable working stress in either tension or compression is 20,000 psi. If the cross section is to be rectangular. Determine the height if the height is to be twice as great as the width. a. 4.62 inch b. 9.24 inch c. 4.06 inch d. 8.12 inch

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

c) The three suspender bars are made of A-36 steel and have equal cross-sectional areas of 450 mm² .Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A B C 80 kN 2 m 50 kN D E F -1m--1m--1 m--1m-|
Determine the reactions of A & B for the steel bon and leasing as given abuming that 4.5 mm clearance exist bin the bar and the ground before the loads are applied. Assume E = 200 GPG. P₁ = 300 KN P₂ = 600 KN A₁ = 250 mm² A₂ = 400 mm² 5 R 4 3 2 1 & P VA 0 B P₂ 150mm 150m 150mm 150mm 4.Sm
Problem 14 , 3 parts ....plz solve all parts I vll upvote
Design a simply supported rectangular reinforced concrete beam. Note: Neglected the self-weight of the beam. Wu (D.L) PLL Wa (L.L) h b W D.L P LL W LL Fc bar No. of Fy MPа MPa (mm) (mm) (m) kN/m kN kN/m dia. layers 325 500 17 50 20 20 two 28 420
Determine the force in member AB of the truss below. Indicate as positive if the member is in tension and negative (-) if the member is in compression. Provide the answer in kips t H 1.5 k F 2 k 2 k G B C . 8 ft 8 ft -8 ft 8 ft E D 4 ft Q Search securySearch 5 17 & 8
Girder AB. Assume Use Fy = 50 ksi and select a shape for that the floor slab provides continuous lateral support. The maximum permissible live load deflection is L/180. The service dead loads consist of a 5-inch-thick reinforced-concrete floor slab (normal weight concrete), a partition load of 20 psf, and 10 psf to account for a suspended ceiling and mechanical equipment. The service live load is 60 psf. a. Use LRFD. b. Use ASD.
A vertical rod is attached at point A to the cast iron hanger shown. The force in the rod is 10 Kips acting downward. Determine (a) the stresses at points C and D, (b) the position of the neutral axis. 1 in. -3 in. A av 1.5 in. 10 Kips a 1.5 in. O B 3 in. C Section a-a D 0.75 in. ↑ 0.75 in. T
M V Д A 5 K X 10'-0" 4" 4" Y Y 12" 12 K Ix = 1024 in 4 ly = 640 in 4 10'-0" 1. The 'Inverted-T' cross section below is used in the orientation shown as a cantilevered beam with two concentrated loads as indicated on the given Loading diagram. to B 4'-0" 12 K Parta Name 5 K a. Calculate the self-weight of this beam in #/ft, assuming a material density of 160 #/ft³ For Parts b-d, ignore the self-weight calculated in Part a b. What is the maximum SHEAR STRESS in the beam? Answer: c. What is the maximum FLEXURAL STRESS in the beam? Answer: 'ch sheet of significant c vided, com ernal refer 1 'm 'owable llowing hir iar d. Locate the Inflection Point along the span of the beam, calculating a specific distance from the Support at B. Indicate the location of this point on the Loading or Moment diagram.
The uniformly distributed live load on the floor plan in the figure given below is 65 lb/ft². Consider the live load reduction if permitted by the ASCE standard. A (B) B2 G3 -6 @ 6.67' = 40- I B4 G4 B1 40' G1 C2 G2 C3 Establish the loading for girder G3. The loading (P) for girder G3 is [ B3 20' kips. (3) 2 @ 10' = 20' I+ 5 @ 8'=40'
What is the value in kips of the axial force in Column C2 on the first story? Floor System All question pertain to the following floor plan. The floor load is 60 lb/ft?. Ignore the self weight of the members. The building is three stories tall. I- I- I- GZ 20 10! C2 B1 ze lo' to I. エ- 30' 25
1. [-/5 Points] DETAILS GGMECHMAT9SI 5.8.004. MY NOTES ASK YOUR TEACHER PRACTICE ANOTHER A simply supported wood beam with overhang is subjected to uniformly distributed load q. [11 1m- 250 mm Ⓡ ¹200 mm' The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value q if the allowable bending stress is all = 11.6 MPa, and the allowable shear stress is Tall = 1.85 MPa. (Enter the magnitude in kN/m.)
1%9. l. In. • f 10 Y:- quiz2.pdf > Quiz: Design the reinforcement steel that necessary for the shcar and torsion for the rectangular cantilever beam shown in figure. Use for stirrups (o12) and let f.=25 MPa, f-400 MPa, dead load (5 kN/m?) and live load (10 kN/m), take into account the self-weight of beam. All dimensions in (mm) 1000 800 3000 300 Cnand TEXTEDT II