A bracket, made of steel (oy=220 N/mm2) and subjected to a force of (P)acting at angle of 30° to the vertical as shown in Fig below The cross-section is rectangular with dimensions, 60 mm x 30 mm the factor of safety is 4, find the value of P. (All dimensions in mm) www sung Quad Camera تم الالتقاط بواسطة Dom 300 mm MINUTA 60 mm T 30 mm 150 mm

A bracket, made of steel (oy=220 N/mm2) and subjected to a force of (P)acting at angle of 30° to the vertical as shown in Fig below The cross-section is rectangular with dimensions, 60 mm x 30 mm the factor of safety is 4, find the value of P. (All dimensions in mm) www sung Quad Camera تم الالتقاط بواسطة Dom 300 mm MINUTA 60 mm T 30 mm 150 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

Find Ixx of the plate shown below. where AB = 2 m, AC=12.5m, EF = 10m, FG = 2.5m, HD=3m. A B (1) E F (Enter only the values in the boxes by referring the unit given in bracket.) C The value of X (in m) = The value of Y (in m) = The value of lw1 (in m) = The value of lw2 (in m4) The value of Ix of the given plate (in m4) =
Find the ox value for the plate as shown below, where b1=d2%=D16 mm, d1=70 mm,b2%=90mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1
The rectangular lamina with breadth = 40 mm, depth = 60 mm. The Ixx value is mm4 Select one: O 10.66 x 104 O 24 x 104 O 72 x 104 O 32 x 104 Friction force always acts in a direction to the direction of motion. Select one: O inear O normal O opposite O perpendicular
Aluminum Rod#1 has a length L and a diameter d. Aluminum Rod#2 has a length 2L and a diameter 2d. If Rod#1 is under tension T and Rod#2 is under tension 2T, how do the changes in length of the two rods compare?
4.14. Calculate I,,Iy,Iyy for the symmetrics Z-section of Figure P4.8
Given a stress state of ø, = -4 MPa, øy = 12 MPa, ty = 7 MPa ccw 1) Draw a properly oriented stress element illustrating this state of stress 2) Using Mohr's circle, find the principal stresses and directions, and show these on a stress element correctly aligned with respect to the xy coordinates. Draw another stress element to show zi and 72, find the corresponding normal stresses, and label the drawing completely. 3) Use the plane-stress transformation equations to validate your answers in part 2
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 48512-Nload, using the following data: length of steel = 1.42 m, length of bronze = 2.36 m Area of steel = 639 mm, Area of bronze = 319 mm Modulus of elasticity of steel = 180 Gpa, Modulus of elasticity of bronze = 81 Gpa x = 0.58 m, y = 1.13 m, and z = 0.72 m. Round off the final answer to two decimal places.
Calcuate Bending From Point A to Point B and Point A to Point C, Calcuate torsion From Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Find the value of stress Force 2.2 N Area=2 m2
Cylinder has a non-uniform density. Find y of the cylinder ( when density is ply) = 5.254 - 2,31 [kg/m²³], radius 3.75 m t theight is 78.17m. 117 2 => My
4. Given: Curb shown below Find: (1) Surface area and (2) volume 100 mm 150 mm 4 m 30° 150 mm 150 mm
Q 2: Find Ixx and lyy of the Lamina shown in Fig. 1 80 30 50 110 30 120 Fig. 1