A block with a mass of 5.00 kg slides down a surface inclined 36.9° to the horizontal Problem 2 as shown in the figure. The coefficient of kinetic friction between the block and the incline is 0.25. A string attached to the block is wrapped around a pulley on a fixed axis at O. The pulley has a mass of 25.0 kg and a moment of inertia 0.500 kg.m². The string pulls without slipping at a perpendicular distance of 0.200 m from the pulley's axis down the incline. (a) What is the acceleration of the block down the plane? (b) What is the tension in the string? 5.00 kg 36.9°

A block with a mass of 5.00 kg slides down a surface inclined 36.9° to the horizontal Problem 2 as shown in the figure. The coefficient of kinetic friction between the block and the incline is 0.25. A string attached to the block is wrapped around a pulley on a fixed axis at O. The pulley has a mass of 25.0 kg and a moment of inertia 0.500 kg.m². The string pulls without slipping at a perpendicular distance of 0.200 m from the pulley's axis down the incline. (a) What is the acceleration of the block down the plane? (b) What is the tension in the string? 5.00 kg 36.9°

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 8CQ: A massless tether with a masses tied to both ends rotates about a fixed axis through the center. Can...

See similar textbooks

Similar questions

What three factors affect the torque created by a force relative to a specific pivot point?
A mass, m₁ = 8.00 kg, is on a 30.0° incline and it is attached to another mass, m₂ = 10.0 kg, on a 60.0° incline. They are attached with a massless rope over a pulley with a moment of inertia, I, and a radius of R = 0.250 m. There is no friction between the table and the blocks. Ignore air friction, too. We are given that my accelerates up the incline at a = 1.00 m/s². (a) Draw a free-body diagram for both masses and the extended free-body diagram for the pulley. (b) Determine T₁ and T₂. (c) Find the net torque acting on the pulley and (d) its moment of inertia.
The uniform solid Rotation axis block in Fig. and edge lengths a = has mass 0.172 kg 3.5 cm, b = 8.4 cm, and c = 1.4 cm. Calculate its ro- tational inertia about an аxis through one corner and perpendicu- lar to the large faces.
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is 0.30 and the weight of the handle is 15 N. Determine the force P that must be applied to the end of the handle to resist a maximum toraue of 75 N m if the torque is applied Clockwise. mm 60 80 80 240 mm mm mm mm
The spool has a weight of 30 lb and a radius of gyration ko 0.45 ft. A cord is wrapped around its inner hub and the end subjected to a horizontal force P = 5 lb. Determine the spool's angular velocity in 4 s starting from rest. Assume the spool rolls without slipping. 0.9 ft 0.3 ft 0 P = 5 lb
A uniform rod of mass m, = 153 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are attached to the rod at the r, = 10.0 cm and r, = 90.0 cm mark, passed over pulleys, and masses of m, = 286 g and m, = 187 g are attached. Your TA asks you to determine the following. (a) The position r, on the rod where you would suspend mass m3 200 g in order to balance the rod and keep it horizontal if released from a horizontal position. In addition, for this case, %3D what force (magnitude and direction) does the pin exert on the rod? Use standard angle notation to determine the direction of the force the pin exerts on the rod. Express the direction of the force the pin exerts on the rod as the angle 0F, measured with respect to the positive x-axis (counterclockwise is positive and clockwise is negative). r3 0.602 m 0.49 F. See if you can write a condition for rotational equilibrium statement that will allow you to determine the position on the rod where we need to…
Calculate the magnitudes of the supporting force Ra and moment Ma at A for the loaded cantilever beam. Assume w= 740 N/m, a= 6.5 m, b= 3.9 m. Answers: RA kN MA kN-m
The two blocks have weights of 5 lb (horizontal motion) and 2 lb (vertical motion). The radius of the pulley is 0.55 ft it and the moment of inertia about its axis is I = 0.4 slug-ft². The coefficient of friction between the 5-lb weight and the horizontal surface is k = 0.2. (Figure 1) Figure 5 lb A B 2 lb
The figure below shows an outstretched arm (0.61 m in length) that is parallel to the floor. The arm is pulling downward against the ring attached to the pulley system, in order to hold the 98 N weight stationary. To pull the arm downward, the latissimus dorsi muscle applies the force M in the figure, at a point that is 0.069 m from the should joint and oriented at an angle of 29°. The arm has a weight of 47 N and a center of gravity (cg) that is located 0.28 m from the shoulder joint. 0.61 m 0.28 m 0.069 m Axis at 98 N shoulder joint cg 29 Aldentify all the forces on the arm and draw an accurate and complete free body diagram on both the arm and the 98 N weight. You may draw on the figure if you wish. B Write down the correct equation of motion ON THE 98 N WEIGHT by summing all the forces acting on it using Newton's 2nd Law of Motion. You must identify and draw your chosen coordinate system. ( Write down the correct equation of motion ON THE ARM by summing all the forces acting on it…
Problem 2: A string is wrapped around a pulley with a radius of 3.0 cm and no appreciable friction in its axle. The pulley is initially not turning. A tangential constant force of 5O N is applied to the string, which does not slip, causing the pulley to rotate and the string to unwind. If the string unwinds 1.5 m in 5.0 s, what is the moment of inertia of the pulley?
A 5 kg block rests on a 28o inclined surface of friction coefficient of 0.37 and is attached by a non-slipping light string over a pulley of mass 27 and moment of inertia I = 0.51 MR2 to a 26kg hanging mass. If g = 9.8 m/s2, what is the tension in the connecting string?
A 9 kg block rests on a 34o inclined surface of friction coefficient of 0.27 and is attached by a non-slipping light string over a pulley of mass 27 and moment of inertia I = 0.32 MR2 to a 19 kg hanging mass. If g = 9.8 m/s2, what is the tension in the connecting string?