A block-and-tackle pulley hoist is suspended in a warehouse by ropes of lengths 2 m and 3 m. The hoist weighs 350 N. The ropes, fastened at different heights, make angles of 50° and 38° with the horizontal. Find the tension in each rope and the magnitude of each tension.

A block-and-tackle pulley hoist is suspended in a warehouse by ropes of lengths 2 m and 3 m. The hoist weighs 350 N. The ropes, fastened at different heights, make angles of 50° and 38° with the horizontal. Find the tension in each rope and the magnitude of each tension.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Related questions

Q: The three identical rollers are stacked on a horizontal surface as shown. If the coefficient of…

A: Introduction Rolling friction and sliding friction are two different forms of friction. When one…

Q: Determine the magnitude of the resultant of the three forces shown F₁ = 70 N 3 5 4 F₂ = 80 N O 33.8…

Q: Cable AB is 65 ft long, and the tension in that cable is 3900lb. Identify the (a) x, y, and z…

Q: crude oil having kinematic viscosity of 0.4×10-4 m2 per second is flowing through a pipe having…

A: Given:Kinematic viscosity, ϑ=0.4×10-4 m2/sDiameter of pipe, d=0.3 mDischarge=300 liter/s=0.3…

Q: 4. Three pounds of a perfect gas with R = 38 ft.lby/lb.R and k = 1.667 have 300 Btu of heat added…

Q: Problem9 The entrance flow between two parallel plates (gap h) has a velocity that varies linearly…

A: In a laminar flow between two parallel plates, the velocity profile is symmetric about the mid-plane…

Q: Initial velocity of the block is 20 m/s and its final velocity is 10 m/s. The block is 2 kg. Y-Z…

Q: a) Based on the representative boundary conditions shown in the figure, draw a free body diagram…

A: According to the question a loading beam ABCDE is given We need to find all the reaction with the…

Q: First we will analyze the situation when P = 500 N. The connection at A is a pin and the connection…

Q: A WT9 x 30 structural steel T-section is loaded and supported as shown below. (a) Draw complete…

Q: Find the Degrees of Freedom A G 3 A H 1 2 B B D C FQ D E A 3 B 2 B 3 C Od 1 2 A 3 3 B Do- T/IMM 1 5…

A: Given data:- To find:-degree of freedom

Q: 11. The work required to compress a gas reversibly according to pv1.30- cis 67, 790 J, if there is…

Q: Q₁: Find the heat transfer rate by adding straight fins of rectangular cross section of length 50 mm…

Q: Problem 11: At time t = 0 a small ball is projected from point A with a velocity of 200 ft/sec at…

Q: Q2: A: For the tanks-system shown below, write the equations (only) of the flow in each tank. Assume…

A: Given: For the tank1: Incoming flow rate=5 gal/min Outgoing flow rate=2+3=5 gal/min Concentration of…

Q: From the diameter of the sun and the earth and the mean distance of sun from earth, estimate (a) the…

A: Diameter of the sun = 1,392,000 km = 1.39 × 109m Diaplanet-Y= 340,800 km = 3.408 × 108m Mean…

Q: 16. 1000CFM of air are compressed at constant temperature of 85°F and 198 psia to 580 psia. For both…

Q: For step one, I got the same values but negative

Q: F F₁ 2 Given the following Variable Value A B C D F₁ F₂ 20 mm 85 mm 20 mm 90 mm 24 N 5 N D F N A…

Q: The least radius of gyration of a ship is 8 m and meta-centric height 70 cm. Calculate the time…

A: Given:Least radius of gyration of ship, k=8 mMeta centric height of the ship, GM=70 cm or 0.7…

Q: a) Explain why some of this problems satisfy and dont satisfy the first and second law of…

A: These questions are based on the concept of Basic laws of Thermodynamics.

Q: A mass of 7.9 kg oscillates at the end of a spring of stiffness 26.1 Nm¹. If the damping ratio is…

Q: A machine member part is subjected to fluctuating stress of a = ax cos(8nt) The endurance limit of…

Q: The pitcher throws the baseball with a release angle of 2 degree below horizontal, and speed of 47…

A: Given data:- release angle (θ)=2° initial velocity V0=47 m/s distance(s) =18.5 m To find:- Time…

Q: 5. A large stationary Brayton cycle gas-turbine power plant delivers a power output of 100 MW to an…

Q: l'aking atmospheric pressure head = 10.3 m of water. A 100 mm diameter horizontal pipe has…

A: Given:pipe diameter=100 mm or 0.1 mcontraction ratio=0.5No flow pressure head=P1ρg=3 m +10.3 m=13.3…

Q: Determine the force in each cord for equilibrium of the 68-kg bucket in (Figure 1).

A: According to the given data Here m=68 kg W=mg=667.08 N We need to find Force in the each member

Q: A physical pendulum starts moving from a position in which its center of mass is directly above the…

Q: Rod OA rotates counterclockwise at a constant angular rate 04 rad/s. The double collar B is…

A: Rod OA rotates at constant angular rate θ.=4 radsec r=(1.6 cos θ) m Mass of both collar 0.7 kg.…

Q: Required information x Rod BD is made of steel (E-29 106 psi) and is used to brace the axially…

A: According to the given data E=29x106psi P=110kips FBD=0.018P δBD=0.0002(AC) We need to find…

Q: Calculate the density and error calculations (kg/m^3) using the following values. (ρ = m/V). Mass =…

A: Given: To find: The density and error calculations (kg/m^3) using the following values. (ρ = m/V).…

Q: A hollow steel square bar with an outside dimension of 100 mm on each side must carry a tensile load…

Q: Explain the application of the first law of thermodynamics to appropriate systems

Q: A quarter car model of an automotive vehicle suspension system is shown in Figure Q2 below, where k,…

A: According to the given data m1=304.3kg m2=36.1kg k1=22kN/m k2=82.2kN/m we need to find First system…

Q: 0.4 m = 0.5 m A B C P 20-mm diameter 60-mm diameter Fig. P2.19 and P2.20 2.20 The rod ABC is made of…

A: Given Data- A stepped rod subjected to forces given We have to find deflection of point A and B…

Q: Heat is absorbed from a cooled space at a rate of 320 kJ/min by R-22, which enters the evaporator at…

Q: 8-hour time-weighted average (TWA) noise exposure for 80.5 dba

A: Given data: Noise Exposure = 80.5dba Time of exposure = 8 hrs To find: TWA

Q: A 200 x 100 x 50 mm steel block is subjected to a 15 MPa. The Young's modulus and Poisson's ratio of…

A: Given:Dimension of steel block=200×100×50 mmHydrostatic pressure=15 MPaE=200 GPaϑ=0.3Find,Change in…

Q: P10 The velocity field of a flow is described byu=4x,v=5y+2, andw=3t2+3. What is the pathline of a…

Q: A water carbonation plant is available for use in your home. It operates by providing CO2 at a…

A: Given: KH (Henry's constant ) in atm/(mol/L) for CO2 at 298K = 29.76 atm/(mol/L) PCO2…

Q: Find the solution to the IVP d²u dt2 +4u = 1, u(0) = 0, du -(0) = 0. dt

A: Given

Q: Parallel plates form a solar collector that covers a roof, as shown in the figure. The plates are…

Q: Problem 4.4 A body of dimensions 1.5 m x 1.0 mx 2 m, weighs 1962 N in water. Find its weight in air.…

A: Given:dimesion of body=1.5 m×1.0 m×2 mweight of body in water=1962 NFind,weight in air?specific…

Q: A mass of 8.0 kg oscillates at the end of a spring of stiffness 28.3 Nm-¹. If the damping ratio is…

Q: Two hundred and fifty pounds of a mixture of 10 mol % propane 20% n-butane, and 70% n-pentane is…

A: Given: Total mass of mixture = 250 lbMass percentage of propane, butane & pentane = 6.63, 17.47…

Q: In a power plant operating with water and steam, the following measurements and observations were…

A: The temperature is 115oC and the phase of the substance is saturated liquid. Based on the above…

Q: A mass of 21.5 kg is vibrating freely at the end of 3 springs connected in parallel. The spring…

Q: . Determine the crippling load for a I-section of dimensions 20 cm × 10 cm × 2 cm and of length 5 m…

Q: A mass of 0.10 kg is attached to a spring. It is pulled 200 mm to the right of its position when the…

A: Given: Mass→m=0.10 Kg Initial amplitude→X1=200 mm=0.2 m Shifting of the mass after each swing=30…

Q: Please create a simple ping pong ball launcher where there is a mechanism for the trigger. And…

A: We have to given a initial launch angle and a launch initial velocity. And according to the initial…

Question

novig size modestib
Beri
N
1-12 12-
60°
37. A block-and-tackle pulley hoist is suspended in a warehouse
ay by ropes of lengths 2 m and 3 m. The hoist weighs 350 N. The
ropes, fastened at different heights, make angles of 50° and th
38° with the horizontal. Find the tension in each rope and the
magnitude of each tension.
50° brd
60°
2 m
38°
3 m
501001
hon sit
44.
45
4

Expert Solution

Step 1

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4 A ski resort chair lift has towers spaced 38 m horizontaly appart. The upper tower is 15 m higher than the previous tower. If the chairs are 12 m horizontally appart and the first chair is 5 m past the lower tower what is the tension on both ends of the cable? 1:37:01 Book The mass of each chair is 350 Kg and the height above the lower tower for each chair's attachment to the cable is 0.58537 m, 4 m, 9.4244 m. Lower Tower Cable Tension = Upper Tower Cable Tension = kN. KN.
After an unfortunate accident occurred at a local warehouse, you were contracted to determine the cause. A jib crane collapsed and injured a worker. An image of this type of crane is shown in the figure.The horizontal steel beam had a mass of 81.70 kg per meter of length, and the tension in the cable was T-11260 N. The crane was rated for a maximum load of 500 kg. If d 5.000 m. s-0.486 m, z- 1.600 m. and h= 1.890 m, what was the magnitude of W₁ (the load on the crane) before the collapse? The acceleration due to gravity is g 9.810 m/s². = WL What was the magnitude of force Fp at the attachment point P? Fp= N W₁
Calculate Tension BD if P = 100 kN. 1m 2.5 m 250 N -1.5 m- 2 m 1.5 m- Use the editor to format your answer
5) Determine the tension developed in the three cables required to support the traffic light, which has a mass of 20 kg. Take h = 3.5 m. (Ans: FAB = 348 N; FAC= 413 N; FAD = 174 N) 6 m D 3 m B 4 m 4 m 4 m 6 m `3 m 3 m 4 m Figure 5 200
Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last digits number pf your IC) 4m 400 KN 10 m B 60 KN 4m 10 m. 157KN 4m 17 m D
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
nis course Hide What would be the maximum weight W of the block, shown in the following figure, so that the tension developed in any cable does not exceed 200 N: 30 40° Select one: Oa 183.6 (Nj Activate Windows Gete Settiros1o activate Win 6 200 (N) s4465(N) Od 89.3 (N
A ski resort chair lift has towers spaced 44 m horizontaly appart. The upper tower is 15 m higher than the previous tower. If the chairs are 14 m horizontally appart and the first chair is 5 m past the lower tower what is the tension on both ends of the cable? The mass of each chair is 350 Kg and the height above the lower tower for each chair's attachment to the cable is 0.55624 m, 4 m, 9.33 m. Lower Tower Cable Tension = Upper Tower Cable Tension = KN. kN.
The mass of the block is mc=41 kg and the angle a=33deg. mc What is the tension in the cable D, TD in N. Give your answer as an integer.
A load weighing P kN aswith AB, AC and AD cables such asare carried. Points A and B are x-axis, Cand D points are on the y-z plane.Specific to your name in the data tableAB, AC and AD cable using ratingsCalculate the forces. P (kn) = 440 L1 (m) = 11 L2 (m) = 10 L3 (m) = 16 L4 (m) = 18 L5 (m) = 16 L6 (m) = 5
4. Solve for the tension in the cable. p=0.20 300 lb 200 Ib
A transmission tower (a truss) for supporting electric wires is shown. The load of wire at D is shown as force F1 at an angle of a and the load of wire at A is shown as force F2 at an angle of B. Using the values given in the table below: F1 (N) F: (N) a (deg) B (deg) w (m) h (m) Value 150 70 30 60 2 a) Find the reaction forces at supports Y and Z. b) Determine the forces supported by members DO, DM, SV, and UX and specify whether the member is in Tension or Compression. M Q B F1 F2 T W X h