(а)An electrical transducer is a sensing device by which the physical, mechanical or opticalquality to be measured is transformed directly by suitable mechanism into an electricalvoltage/current proportional to the input measurement.i.State THREE (3) advantages of electrical transducer.The applied voltage, Vin is 5 V with the total resistance of the potentiometer R. andR is 5 kn and the total resistance of the potentiometer R. and Ra is 10 kQ,respectively. If the initial position to be used as a reference point is set such that R =Ro (shaft at the mid-stroke), design for a balanced bridge (i.e. VẸ = 0) for apotentiometer transducer with a shaft stroke of 2.0 mm.i.%3D%3D(b) Referring to Figure 5(a) the instrumentation amplifier that has been used to amplify signalsof an instrumentation system. If the output of the amplifier Al is given asVoi(V1-V2)+V1, prove that the gain for differential amplifier A3 is, G= (2+1).R2R;

“Since you have asked multiple question, we will solve the first question for you. If you want any…

(а) An electrical transducer is a sensing device by which the physical, mechanical or optical quality to be measured is transformed directly by suitable mechanism into an electrical voltage/current proportional to the input measurement. i. State THREE (3) advantages of electrical transducer. ii. The applied voltage, Vin is 5 V with the total resistance of the potentiometer R, and Ro is 5 kn and the total resistance of the potentiometer R. and Ra is 10 kn, respectively. If the initial position to be used as a reference point is set such that R = Ro (shaft at the mid-stroke), design for a balanced bridge (i.e. VE = 0) for a potentiometer transducer with a shaft stroke of 2.0 mm. %3D %3D

(а) An electrical transducer is a sensing device by which the physical, mechanical or optical quality to be measured is transformed directly by suitable mechanism into an electrical voltage/current proportional to the input measurement. i. State THREE (3) advantages of electrical transducer. ii. The applied voltage, Vin is 5 V with the total resistance of the potentiometer R, and Ro is 5 kn and the total resistance of the potentiometer R. and Ra is 10 kn, respectively. If the initial position to be used as a reference point is set such that R = Ro (shaft at the mid-stroke), design for a balanced bridge (i.e. VE = 0) for a potentiometer transducer with a shaft stroke of 2.0 mm. %3D %3D

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

1. A voltage regulator with a no-load output dc voltage of 12 V is connected to a load with a resistance of 10 ohms. If the load resistance decreases to 7.5 ohms, the load voltage will decrease to 10.9 V. What is the percent load regulation, and calculate the load current. 2. Determine the amount of anode voltage needed to turn on the PUT in the circuit as shown. Also determine oscillating frequency. R₁ • 470 ΚΩ +18 V AO 0.22 μF WI Va=+9 V -OK www R₂ 2202 R₂ ' 10 ΚΩ R₂ • 10 ΚΩ
Discussion : (1) رم طرة what are the advantăge and disadventage of full-wave bridge rectifier cutcuit- calculate ale practically result have been produced (2) Vpeak theortically of voltage output by using реа (3) üG Compare theortically and practically results. (4) What happens do on Vout, if we reversed the four diodes connects . sKetch the Vout in this case . 6. し 2.5 1.48 1.35
The following waveforms are measured on the input and output of a rectifier while driving a resistive load of 52. For a given value Ix-69 (see Appendix A) and through analysis of the respective waveforms, specify, 36) the supply frequency; 37) the peak value of the input voltage (Vm): 38) the rectifier pulse number; 39) the average output current; 40) the Lm.s, value of the output current; 41) the Lms, value of the harmonics present in the output current; 42) the ripple current peak tot peak; 43) the ripple factor of the output current. Vm Input voltage Ix Output current 10m 20m 40m Time (15)
2 - Which of the following methods cannot be used to determine the terminal names of the LED diode? A) Long connector ANOT, short connector KATOTB) Large plate KATOT inside diode, small plate ANOTC) The cut side in the diode body is KATOT, the other is ANOT.D) With the measuring instrument, the diode stage can be determined with +/- tip.E) Thick connector ANOT, thin connector KATOT
7:-V O Voltage_Doubler_. > Vin = 5 Vpk RI = 4KQ C1-10μF C1 = 10µF Second Year Electronics Laboratory Discussion: 1. Compare the characteristies of voltage doubler with an ordinary a.c to d.c rectifier 2. Discuss the possibit ty of using the voltage doubler circuit as a regulated power su ly. 3. Suggest u circuit d.agram for a voltage tripller and compare it with the voltage doubler circuit. Table (1) Rr. (KO) V. (V) Vip-p (V) Va (V) V.R 10 4. النقطة الثانية في المناقشة غير مطلوبة II
Among its products is the power transducer. The product is an electrical isolation transducer of single-phase active and reactive power measurement, complete isolation between input and output signals. It is designed to measure power, reactive power and power factor. The product is widely used in electricity, communications, railways, industrial control and other fields. The transducer weights 0.7-pound, 1-500-volt, 0.5-700 A, the size is 76mmx32mmx2inch. The response time of the transducer is 250 ms. (a) 1. What is the volume of the transducer in cubic m? 2. How many transducers can be packed in box of 1m X 0.5 m X Qm? 3. If the factory produces 500 transducer per hour, how many minutes are needed to produce 50 kg of the transducer? 4. If the production line needs maintenance every 100,000 transducer. Find to the nearest integer how many weeks are needed to be sent to maintenance if the production rate is 100 transducer/min which operates 8 hours/ day and 5 days / week.
3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991
Question No. 2a. In an Experiment, a high speed diode is to be used. The experimentalist has the liberty to make the diode with Si, Ge or GaAs. Which one would you prefer and why? b. Design a circuit for 5V DC from 12 V DC. Explain your circuit. c. Figure ‘a’ represents the input signal to a circuit which gives the output as the waveform ‘b’. Design the circuit and explain the working in detail
In the given period,(diodes will be considered ideal.a) Draw the V0 output by calculating it according to the input.b) Calculate the average and effective value of the V0 output.c) What are the advantages and disadvantages of using two diodes and two resistors instead of four diodes?Input signal Vm = ± 10V (peak to peak), T = 2π (period),R = 7 kΩ
For a bridge rectifier Assuming the diodes to be ideal, determine (a) d.c. output voltage, (b) peak inverse Voltage of diode, (c) output frequency (d) voltage drop cross RL Given: Vm =81.3 V , RL = 200 Q and fin = . 50 HZ ث إضافة ملف
The following waveforms are measured on the input and output of a rectifier while driving a resistive load of 5 ohms. For a given value Ix=65 and through analysis of the respective waveforms, specify, calculate 39) the average output current; 40)the r.m.s value of the output current 41)the r.m.s value of the harmonic present in the output current
(a) Figure 1(a) is a sinusoidal oscillator. Given that the feedback factor is: R³ B === V₂ By assuming no loading effect, i) State the function of diodes D₁ and D2. ii) Obtain the expression for oscillation frequency f, and calculate its value. iii) Prove that during oscillation, V₁ R³+j- 1 5R .6R² @³C³ w²C² @C iv) Calculate the value of R₂ that will allow this circuit to start and maintain oscillation. Proof that the calculated value will be able to start and maintain oscillation. 2R 200Ω с 0.1 μF 2R 200Ω B = V₂ R₁ 0.5ΚΩ D1 +4 R 10092 D2 с 0.1 μF HE R₂ +15V -15V с 0.1 μF R 10092 - Vo