A 30-kVA, 8000/230-V distribution transformer has impedance referred to the primary of 20 + j100 N. The components of the excitation branch referred to the primary side are Rc = 100 kN and Xm = 20 kQ. (a) Draw the approximated equivalent referred to the primary side. (b) If the primary voltage is 7967 V and the load impedance is ZL = 2.0 +j0.7 N, what is the secondary terminal voltage of the transformer? What is the voltage regulation of the transformer? (c) If the load is disconnected and a capacitor of -j3.0 Q is connected in its place, what is the secondary voltage of the transformer? What is the voltage regulation under these conditions?

A 30-kVA, 8000/230-V distribution transformer has impedance referred to the primary of 20 + j100 N. The components of the excitation branch referred to the primary side are Rc = 100 kN and Xm = 20 kQ. (a) Draw the approximated equivalent referred to the primary side. (b) If the primary voltage is 7967 V and the load impedance is ZL = 2.0 +j0.7 N, what is the secondary terminal voltage of the transformer? What is the voltage regulation of the transformer? (c) If the load is disconnected and a capacitor of -j3.0 Q is connected in its place, what is the secondary voltage of the transformer? What is the voltage regulation under these conditions?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.5MCQ: For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is...

See similar textbooks

Similar questions

Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a three-phase Ynyn0 connected transformer. The equivalent impedance per reduced phase of the transformer to the primary is Zeq1= 1+j5 Ohm. The nominal primary voltage is V1Ln= 5920 V and the conversion ratio is a= 10. what is the amplitude of the actual voltage falling on one phase of the specified load? (simplified equivalent circuit will be used).
D = 0.9 1.5° and B = 150 65° has at the load end a The load voltage and current are V₁ and I₁ A' B' VL B][Y and evaluate these constants. C' D' IL A long line with A transformer having series impedance Zr Obtain expression for Vs and Is in the form 10067°. [$]-[ =
Q2) For the linear transformer shown in figure below, find: a) Construct a frequency – domain equivalent circuit of the system b) Calculate the self – impedance of the primary circuit. c) Calculate the self – impedance of the secondary circuit. d) Calculate the impedance reflected into the primary winding. e) Calculate the scaling factor of the reflected impedance. 42 -j62 1:2 ww 120/0° V rms 20 N ll
The impedance ZL in the circuit shown in Figure is adjusted for maximumaverage power transfer to itself.(a) What should be the value of ZL?(b) What is the maximum average power delivered to ZL?(c) What percentage of the average power delivered to the linear transformer is delivered to ZL?
Given Zo-j407 2, R₁143, R6317 52 and a 0.04, what is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ ww Answer: Zc Zc R₁ Use up to 2 digits after the decimal point if necessary in your answer below VL-28020 V TR
A 480V/240V, 60Hz single transformer has Z1 = 0.1+j0.22 ohms and Z2 = 0.035 + j0.12 ohm. Find the equivalent impedance in ohm referred to the secondary. Group of answer choices 0.07+j0.135 0.06+j0.175 0.04+j0.135 0.06+j0.135
One side of a transformer has What is the voltage (in V rms) at the secondary? 1,800 turns while the other side has 450 turns. The high voltage side is connected to a 240 Vrms source. The low What is the current (in A rms) at the secondary? What is the current (in A rms) out of the source? What is the value of the load impedance when referred to the primary? • Referred impedance = voltage side (secondary) is connected to an impedance ZL = 20 + j10 Q. Provide at least 4 digits after the decimal point. +j_ N What is the value of the source voltage (in V rms) when referred to the secondary?
The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
Determine the ratio of the kW output of transformer A to the kW output of transformer B. Both transformer have equal ratings and turns ration. Transformers A and B are connected in parallel to serve a 750-A single phase load at 0.85 pf lagging. The equivalent impedance of the transformers are 2.5 + j3.75 and 2.875 + j6.25 omhs, respectively.