A 3.25 m long (L) steel pipe has a mass of 625 kg and is lifted by a crane attached to cable CD. Point C is attached to each end of the pipe at A and B of the steel pipe. The length AC is 2.85 m and the length BC is also 2.85 m (i.e., length AC BC). Using g = 9.81 m/s2, calculate the tension in sling AC and give your answer in newtons (N) to the nearest newton.

A 3.25 m long (L) steel pipe has a mass of 625 kg and is lifted by a crane attached to cable CD. Point C is attached to each end of the pipe at A and B of the steel pipe. The length AC is 2.85 m and the length BC is also 2.85 m (i.e., length AC BC). Using g = 9.81 m/s2, calculate the tension in sling AC and give your answer in newtons (N) to the nearest newton.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter table. Find the tension in the 3 cables. @ 080 2021 Cathy Zupke parameter L₁ L₂ L3 L4 M B value 4 1 2 8 10 M C units m m m m kg The tension in cable AB is 0 The tension in cable BC is 202 The tension in cable BD is Z -1₂- XN XN N y
ク一 L13 L/2 L/2 B. Prob. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3. 60 in., and weighs 21 lb;/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y = do/2 at the same cross-section (i.e. at L/2 from the point A).
A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter table. Find the tension in the 3 cables. L4 A cc 080 BY NO SA 2021 Cathy Zupke B parameter value 4 1 2 8 10 L₁ L₂ L3 L4 M The tension in cable AB is The tension in cable BC is The tension in cable BD is M C units |εεεε m m m m kg Z N N IN y
A crate weighs 810 lb and is hung by three ropes attached to a steel ring at A such that the top surface is parallel to the xy plane. Point A is located at a height of h = 50 in above the top of the crate directly over the geometric center of the top surface. Use the dimensions given in the table below to determine the tension in each of the three ropes. ↑Z 2013 Michael Swanbom (сс 00 BY NC SA Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 30 in 43 in 4.5 in a b C y The tension in rope AB is 0.15 The tension in rope AC is The tension in rope AD is x pounds pounds pounds
L/3 L/2 L/2 B. A The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L = 32 ft., do = 4. 50 in., and d; = 3. 60 in., and weighs 21 lb;/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y= d/2 at the same cross-section (i.e. at L/2 from the point A).
A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel barshaving fy = 414 MPa and fc’ = 21 MPa as shown in the figure. The column is to resist a factoredload of 1200 kN and factored moment of 280 kNm. Using the interactiondiagram, determine the following:a. eccentricity, eb. steel ratioc. diameter of the steel bars
A circular beam carries a concentrated and a distributed load as shown in the figure. Determine the following unknowns if the modulus of elasticity is 90GPA and the maximum shear is 508.4kN. USE ANY METHOD Let, P=190KN, a=2m, b=1m and c=3m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P 5w 2w A B a b b If the deflection at the free end (leftmost part of the beam) is equal to -51.476603223441mm, Determine the radius of the cross-section of the circular beam. Determine the slope at the free end of the beam (in degrees).
A design model for a transmission-line tower is shown in the figure. Members GH, FG, OP, and NO are insulated cables; all other members are steel bars. (write answers in kN in 2 decimals) Sign Convention: Tension--> (+) Compression--> (-) 1. compute the force in member EJ
A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. What normal tension ( N ) is required in order that the effect of sag will be eliminated when the tape is supported at end points only? The standard pull is 10kg. Tape area is 8 mm2. E = 200 GPa. need answers and solutions asap, thank you!
A 200-mm diameter pulley is prevented from rotating to 60-mm diameter shaft by a 70-mm long key. If a torque T = 2.2 kN.m is applied to the shaft, determine the width b (mm) if the allowable stress in the key is 60 MPa. 70 mm Shaft 그0 200 mm-e Shaft 60 mm-s-
A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is 0.25, determine the corresponding tension in portion BC of the rope. 25 C D 50 kg m