A 2m by 3m flat plate is suspended in a room, and is subjected to air flow parallel to its surfaces along its 3m long side as shown in the figure. The free stream air temperature, T, is 20°C and the velocity is 7 m/s. The total drag force acting on the plate is measured to be 0.86 N. Determine the average convection heat transfer coefficient for the plate. Air 20°C, 7 m/s L = 3 m

A 2m by 3m flat plate is suspended in a room, and is subjected to air flow parallel to its surfaces along its 3m long side as shown in the figure. The free stream air temperature, T, is 20°C and the velocity is 7 m/s. The total drag force acting on the plate is measured to be 0.86 N. Determine the average convection heat transfer coefficient for the plate. Air 20°C, 7 m/s L = 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An approximation for the boundary-layer shape in is the formula u(y) - U sin 0 sys d where U is the stream velocity far from the wall and d is the boundary layer thickness, as in Fig. If the fluid is helium at 20°C and 1 atm, and if U = 10.8 m/s and 8= 3 cm, use the formula to (a) estimate the wall shear stress Tw in Pa, and (b) find the position in the boundary layer where t is one-half of Tw. -- y = 6 u(y)
Consider laminar flow entering a tube. Before the fluid enters, the velocity profile is constant and equal to to. The tube diameter is D and radius R. You are interested in estimating how much distance the fluid must travel into the tube before the classic Poiseuille parabolic velocity profile is established - this distance is called the "entrance length" or Zent- Using boundary layer theory, which of the following would be a reasonable estimate? (Hint: assume as flow enters the tube, you can model the growing viscous boundary layer as laminar flow over a flat plate, and note that the De where v = Reynolds number for a tube is Rep %3D Zent = (Rep) Zent = D 2 (Rep) Zent = 2. Rep - Rep O Zent R-Rep %3D O None of the above.
i just need final answer Air with uniform velocity of U is flowing over flat square-shape plates with different arrangements given infigure below. One plate is used in arrangement (a), whereas four square plates are used in the arrangement (b)All the plates are the same size. What is the frictional forces ratio (F/F)? (Note: Assume laminar boundarylayer condition along the plate arrangements)
Given engine oil at 60 oC flows over the upper surface of a 5 m long flat plate which temperature is 20 oC. Justify the value of x (m2/s) to get the turbulent flow for the total drag force and the rate of heat transfer per unit width of the plate. Discuss your idea.
Consider an airflow over the surface of a flat plate with a temperature Ts = 250 °C. At some distance from y the origin, the temperature profile of the airflow is given by the following function: q/A As, Ts T(y) = T, -(T. -T3)exp -u. y a fluido dAs The airflow at atmospheric pressure has a free flow velocity u.. = 0.06 m/s and a temperature T = 15°C. The thermal diffusivity of the fluid is aluid = 3.872E-05 m?/s and its thermal conductivity Afluid = 0.03383 W/(m K). 1. Determine the heat flux over the surface of the plate. q/A = W/m? 2. Determine the convection coefficient of the airflow. h = W/(m² K)
(1) Experiments show that in a slightly Viscorur flund at on a молод high speeds the drag force fo exerted on body depends on several parametes. An engineer assumes that the drag force fo is a functon of the budy width normal to the upstream Velocity, I upstream Velouty, ✓, the upstream flud veElucay P viscosity, M, speed of sound, I and the airfoils surface roughnars. " use the Buckingham ♬ Theorem to determine the functional dependence of to on non-dimensional flow similarity parameters (2:) Lot the transition to turbulence occur when I = 1.01m, V= 1·01m/s and M₁P = 1:01·10⁰5 m² s. Calculate the transchen Reynolds number, Retrains.
QI/ If the velocity profile of the boundary layer is :O find the thickness of boundary layer, the shear stress at trailing edge and the drag force on one side of plate 2 m long, if it is immersed in water flowing with velocity of 0.4 m/s (p 998 D = 1.007*10-6 m2/s %3D
Air flows over a stationary flat plate at speed of 4,3 m/s. Plate has a width of 1 m. Air has a density of 1.2 kg/m³ and kinematic viscosity of 1.5x 105 m²/s. Consider plate is totally in air flow field and upper and lower surfaces are identical a) Calculate maximum length of the plate to have a fully laminar flow (in m) Yanıt: b) Calculate total frictional force on the plate considering two surfaces (in N) Yanıt: c) In order to eliminate the frictional force on its surfaces calculate the plate speed (in m/s) Yanıt:
Consider liquid in a cylindrical tank. Both the tank and the liquid rotate as a rigid body. The free surface of the liquid is exposed to room air. Surface tension effects are negligible. Present the boundary conditions required to solve this problem. Specifically, what are the velocity boundary conditions in terms of cylindrical coordinates (r, 0, z) and velocity components (ur, uo, U:) at all surfaces, including the tank walls and the free surface? What pressure boundary conditions are appropriate for this flow field? Explain. Free surface Ps Paa Liquid
a stone is thrown from top of 35m tall bilding. The stone is thrown with an initail speed of 15 m/s at an angle 53 degrees above the horizintal. If air resistance is negligible, what is the angle at which the stone will hit the ground?
Air flows over a stationary flat plate at speed of 4,6 m/s . Plate has a width of 1 m. Air has a density of 1.2 kg/m3 and kinematic viscosity of 1.5x 10-5 m 2/s . Consider plate is totally in air flow field and upper and lower surfaces are identical a) Calculate maximum length of the plate to have a fully laminar flow (in m) b) Calculate total frictional force on the plate considering two surfaces (in N) c) In order to eliminate the frictional force on its surfaces calculate the plate speed(in m/s)
Engine oil at 100°C flows on the top surface of a 1-m-long flat plate maintained at 20°C. The oil’s freestream speed (u infinity) is 0.1 m/s. Find the engine oil properties from the table A.5 A. Evaluate the Reynolds number, local convection coefficient, heat flux and shear stress at the end of the plate (x = L). Is the air flow laminar or turbulent over the plate?B. Evaluate the average convection coefficient, average heat flux, average shear stress and drag force over the plate.