A 240V, 60 Hz source is suppling power the following loads Load 1: 10kVA @ pf = 0.55 lagging Load 2: 5kVA @ pf = 1 Load 3: 3kVAR @ pf = 0.60 leading Calculate the current total complex power and power factor ST= ST= pf = 2 untis lagging, leading, or unity Calculate the total current before power factor correction ITbefore = units units Calculate the total current after power factor correction | Tafter= units +j units If its desired to have a unity power factor, how much capcitive reactive power needs to be supplied to the network? Qneed= units

A 240V, 60 Hz source is suppling power the following loads Load 1: 10kVA @ pf = 0.55 lagging Load 2: 5kVA @ pf = 1 Load 3: 3kVAR @ pf = 0.60 leading Calculate the current total complex power and power factor ST= ST= pf = 2 untis lagging, leading, or unity Calculate the total current before power factor correction ITbefore = units units Calculate the total current after power factor correction | Tafter= units +j units If its desired to have a unity power factor, how much capcitive reactive power needs to be supplied to the network? Qneed= units

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
4. Design the network in the figure to have the following characteristics: i. BW - 500 Hz ii. Qp = 30 iii. Vemax = 1.8 V 0.2 mA Z0° C7 R, = 0 N
Question 3 To reduce the power consumption, the capacitors Complete should be located Marked out of 1.00 O a. As far as possible to the load P Flag question b. Not suitable place O c. As close as possible to the load d. Not too close not too far from the load Question 4 A load 200+j0 ohms is connected across a 250 V and Complete 50 Hz supply. Find the reactive power. Marked out of 1.00 O a. 350 VAR P Flag question O b. 360 VAR O C. zero VAR Od. 420 VAR
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
Question 6 20020°V L rms In the circuit in the figure; L load draws 15 kVA with lagging power factor 0.6. • The load L 2 draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the reactive power for the loadL ? 1 9000 O -3600 O 2700 O 12000 O 4800 O 4500 No new data has been saved. The latest contact is at16I01
During fast decoupled Method load flow analysis in one of the loads the calculated reactive power was found as - 0.8 p.u. and change in reactive power as -3.2 p.u. According to you which one of the following choices will have the value of Specified reactive power at the load bus? Select one: O a. -4.0 p.u. O b. -2.4 p.u O C.2.2 d. +4.0 p.u.
Two impedances, Z1 = 2+j6 N and Z2 = 6-j12 N are connected in series with a 220-V 60-Hz supply. At what frequency will the circuit act as a purely resistive load? O 84.85 Hz O 116.62 Hz O 82.46 Hz O 120 Hz
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
A 15µF capacitor and a 470 ohm resistor are connected in series with a function generator. The supply voltage is 50V RMS 40Hz. Find the reactive power for this circuit.
In series reactive power compensation, the Xc = 6.99 ohm and XL = 6.72 ohm, then the degree of compensation k is Degree of compensation k