A 15 KVA, 10.8 KV/240-V, 60 Hz, single-phase conventional transformer is supplying 10 KW of power to a load at 0.85 Lagging power factor, a load voltage of 240 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. 0.225+j1.25 02 +0 -0 Th+es 76852 Select one: O a. V₂ = 10800 Volts O b. None Oc V₂ = 12.84 KV O d. V₂ = 11.26 KV www ES ms j208.33 Q 0+

A 15 KVA, 10.8 KV/240-V, 60 Hz, single-phase conventional transformer is supplying 10 KW of power to a load at 0.85 Lagging power factor, a load voltage of 240 Volts. Its Equivalent circuit is given below. Calculate the magnitude of the input voltage of this transformer. 0.225+j1.25 02 +0 -0 Th+es 76852 Select one: O a. V₂ = 10800 Volts O b. None Oc V₂ = 12.84 KV O d. V₂ = 11.26 KV www ES ms j208.33 Q 0+

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
1) Calculate the maximum RMS current in p.u. that guarantees the equality of losses between the deformed and non-deformed regime for a power transformer equal to 400 kVA with Pcp = 6% in two cases: a) the transformer feeds a twelve-phase converter Idc=40 A b) the transformer feeds a six-phase converter Idc=40 A.
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
1-A single-phase power system is shown in Figure below. The power source feeds a 100- kVA 14/2.4-kV transformer through a feeder impedance of 40.0 + j150 &. The transformer's equivalent series impedance referred to its low-voltage side is 0.12 + j0.5 &. The load on the transformer is 90 kW at 0.80 PF lagging and 2300 V. 40n j150n 0.12n j0.5n Load 90 kW 0.85 PF lagging source Source Feeder Transformer Load (transmission line) (a) What is the voltage at the power source of the system? (b) What is the power losses in the feeder?
A step-up transformer is designed so that the output of its secondary winding is 2,200 V (rms) when the primary winding is connected to a 210 V (rms) line voltage. (a) If there are 180 turns in the primary winding, how many turns are there in the secondary winding? turns (b) If a resistor connected across the secondary winding draws an rms current of 0.55 A, what is the current (in A) in the primary winding? A
A single-phase transformer has a voltage ratio on open circuit of 7900/660 V. The primary and secondary resistances are 0.55 ohm and 0.035 ohm respectively. The corresponding leakage reactances being 4.22 ohm and 0.18 ohm. The load is equivalent to a coil of resistance 3.85 ohm and inductive reactance of 4.2 ohm. Determine the terminal voltage of the transformer and the output in kW when supplying a given load using approximate equivalent circuit when the applied voltage is 7912 V. Your answer
The net cross section of a transformer is 20 square inches. The maximum fluxdensity is 11 kilogausses. The frequency is 60 Hz. If there are 1,000 turns in theprimary, determine the primary induced emf.