A 120V (rms), 60Hz three-phase system is supplying power to the following two loads: Load # 1: A balanced load connected in wye with 100ohm resistance and 0.1H inductor connected in series. Load # 2: A balanced load connected in delta with 100ohm resistance and 10uF capacitor connected in series. Draw a circuit diagram and Determine: (i) Total active and reactive power supplied to load # 1 by the system (ii) Total active and reactive power supplied to load # 2 by the system (iii) Magnitude of the total current supplied by the source (iv) Source power factor

A 120V (rms), 60Hz three-phase system is supplying power to the following two loads: Load # 1: A balanced load connected in wye with 100ohm resistance and 0.1H inductor connected in series. Load # 2: A balanced load connected in delta with 100ohm resistance and 10uF capacitor connected in series. Draw a circuit diagram and Determine: (i) Total active and reactive power supplied to load # 1 by the system (ii) Total active and reactive power supplied to load # 2 by the system (iii) Magnitude of the total current supplied by the source (iv) Source power factor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms