Show complete solution If a 10KN 100mm diameter plunger is applied on a 100 mm thick block. the shaering stressdeveloped on the blockWhat force is required to punch a 25 mm diameter hole in a plate that is 25 mm thick if the shearstrength idevelopA hollow steel tube with an inside diameter of 100 mm carry a tensile load of 400 KN. If the stressis limited to 120 MPa,

As per guidelines we need to answer only first question so please repost rest questions separately.

Answered: a 10KN 100mm diameter plunger is…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A and loaded as shown. Which of the following gives the maximum average normal stress in the system shown? 6P 4P A5.5 P/A B.4.5 P/A 3A 2A A 3P C.4 P/A D.3 P/A 4P 6P Which of the following is the highest value of stress within the strain hardening region of a typical elasto-plastic material subjected to tensile test? A. Elastic Limit B.Yield Stress C.Ultimate Stress D.Proportional Limit What is the lateral strain of a uniaxially loaded member if its longitudinal strain is 0.02 and its Poisson's ratio is equal to 0.3? A.+0.006 B.-0.006 C.+0.667 D.-0.667 Which of the following is the highest value of stress within the elastic region of a typical elasto-plastic material subjected to tensile test? A.Yield Stress B.Elastic Limit C.Ultimate Stress D.Proportional Limit
A punch of 20 mm diameter is used to punch a hole in 8 mm thick plate. If the force required to create a hole is 110 kN, the average shear stress in the plate will be nearly (a) 410 MPa (b) 320 MPa (c) 220 MPa (d) 140 MPa 95
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
A threaded steel rod (Es = 210 GPa, dr = 12 mm, as = 12 x 10-6/°C) is held stress free between rigid walls by a clevis and pin (dp = 15 mm) assembly at each end. If the allowable shear stress in the pin is 45 MPa and the allowable normal stress in the rod is 70 MPa, what will be the maximum permissible temperature drop AT? pin, dp ΔΤ rod, d, Clevis
A plate having a width of 300mm and a thickness of 20mm is to be connected to two plates with thickness of 12mm by four rivets. The allowable shear stress for the rivets is 150 MPa and for bearing is 1.35 Fy. If the yield strength and the ultimate strength is 248 MPa and 400 MPa respectively. Determine the Following: a.) Required diameter of rivets w/o exceeding the aloowable stress in the shear. b.) Required diameter of rivets w/o exceeding the allowable stress in bearing. c.) Required diameter of rivets w/o exceeding the allowable stress in tension.
A 5 mm thick hollow steel rectangular tube must carry a tensile load of 200 kN. If the stress is limited to 100 MPa, which of the following sections can carry the given load. *
A plate of 150 mm width and 20 mm thick is welded to another plate by fillet weld as shown in the figure. The size of the weld is 12 mm throughout. Compute the average shear stress produced in the weld for the full strength of the plate if the allowable stress is 150 N/mm². 70.72 mm 70.72 mm 14 150 mm 150 mm ► 60 mm dia 150 mm
Q.1. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detemine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mm*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN'm2. Punchar 25 mm 26 mm 30 mm thick
Problem 3.2 (CE BOARD NOVEMBER 2003, CE BOARD NOVEMBER 2004) The lower ends of the three bars shown are at the same level before the 18 Mg block is attached. Each steel bar has an area of 600 mm 2 and E = 200 GPa. For the bronze rod, the area is 900 mm^2 and E broaze = 83 GPa. Fteel steel Sm a) Find the stress in the bronze rod. b) Calculate the axial stress in the steel rod c) Detemine the elongation of each rod.
A steel tube with 3cm outside diameter, 0.25cm thick, and 4m long is covered and lined throughout with copper tubes 0.20cm thick. The three tubes are joined together at their ends. What is the maximum compressive load that can be applied to the top such that the total deformation does not exceed 0.50mm? Esteel = 200 GPa & Ecopper = 110 GPa.
The normal stress at point A equals to The shearing stress at point A equals to 400 mm 200 mm 2kN 1kN - 20 mm Section a-a

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS