8. In what way should you connect an ammeter to an electronic component to correctly measure the electric current flowing in it? • Connect it in parallel with the electronic component because current flowing in parallel branches is the same for each branch. • Connect it in series with the electronic component because current flowing in series connections is the same all throughout. 9. How should you connect a voltmeter to a component to get the correct voltage drop in that component? *

8. In what way should you connect an ammeter to an electronic component to correctly measure the electric current flowing in it? • Connect it in parallel with the electronic component because current flowing in parallel branches is the same for each branch. • Connect it in series with the electronic component because current flowing in series connections is the same all throughout. 9. How should you connect a voltmeter to a component to get the correct voltage drop in that component? *

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter53: The 555 Timer

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

2. Figure 1 shows a sensor consists of a core, an armature and a variable air gap. The core with 3.0 cm depth and 10000 relative permeability has 200 coil turns. On the other hand, the armature is a steel plate of thickness 0.2 cm and has similar relative permeability with the core. Assuming the relative permeability of air is unity and the permeability of free space is equal to 4x x 10-7 H.m, calculate the inductance of the sensor for air gaps of 0 mm and 2 mm. Please write the answers in 3 decimal places. 2.0 cm 1.0 cm 6.0 cm 3.0 cm 1.5 cm Figure I
The voltage drops across a 28 ohm resistor is 52 v. What is the voltage drop across a 63 ohm resistor that is in series with the first one? (Resistors in series have voltage drops proportional to their resistance) Need to show work
If the frequency of a waveform is 50 Hz, then the time period of the waveform is O a. 0.2 msec O b. 0.002 msec O c. 2 sec o d. 0.02 Sec
For a pressure to voltage sensor, when 500 bar is applied the coherent output voltage being 5volts, If the applied pressure increases to 1kilo-bar. The voltage is changed to kilo-volts. O 10 O 0.010 O 0.100 O 100
Еxample: Derive the formula : Sinhx = In(x+Vx' +1)
For a pressure to voltage sensor, when 500 bar is applied the coherent output voltage being Svolts, If the applied pressure increases to 1kilo-bar. The voltage is changed to kilo-volts. O 10 O 0.010 O 0.100 O 100
2. [5 points] (a) Vs (b) R Rx IG contact Ammeter A A potentiometer is to be used to measure the voltage Vm as shown above. L is the length of the potentiometer and x is the length of resistance to the contact point when the measurement is ready to be taken. VmRm What conditions are required for a measurement to be taken? Does this place the system in null or deflection mode for the measurement? How is Vm calculated from the measured length x? Provide a mathematical expression. No written explanation required.
Measurement systems that contain elements do not respond instantaneously to changes in the input signal. In other words, they always have some Lag in response. capacitance impedance resistance inertance
Which performance tests should be performed on the patient rotating apparatus shown in the picture, why should they be done and how should they be done. In addition, there are heating pads working with the logic of electric blankets in this apparatus, please answer by taking this into account when answering. (For example: burn testing, water-resistance test, load test, material testing, stress testing, ISO 10993-5, ISO 10993-10, etc.) The main part of the product consists of a polyurethane sponge. Stain-proof upholstery fabric will be used as the outer surface material.
3) The probe in AFM techniques is 4) Nanoscale materials are so interesting, especially in the industry sector due to 5) and and------ are considered one of the important metal nanoparticles that are used as vigorous catalysts in chemical reactions. 6) The synthesis process of nanoparticles that use the liquid phase as bulk materials is process. 7) The process that uses ultrasound frequency greater than 20 kHz is known as process. is outside the sphere. 8) The process that depends on using atom by atom to fabricate nanoparticles are called 9) Micelles are called reverse micelles if is inside the sphere and 10) The pressure equal to 50 Torr is normally equal to ------Pa.
3. (i) Three identical capacitors are connected in delta with 400 V. If the line current is 12 A determine the capacitance of each of the capacitors. If the 0 60° then calculate the power dissipation in kW when it is connected in STAR ENGG_AC_Quiz-Format_01/2016-17_V02 (ii) Three coils each having resistance 6Q and inductance are connected in star with 415V. If the line current is 30 A, find the value of inductive reactance as well as inductance value. If 0 45° then calculate the power dissipation in kW when it is connected in Delta.
Question / Draw an accelerometer sensitivity curve and discuss the useful frequency range. In thesame plot also show the effect of increased accelerometer mass? (Please answer it in very easy way easy to rememeber for revsison )