7.73. This nozzle discharges ideal liquid of specific weight 9.80 kN/m³ to the atmosphere. The velocity in the pipe is 3.0 m/s. The velocity through the jet may be assumed to vary linearly from top to bottom. The nozzle is of such shape that the weight of liquid contained therein is 135.0 N, with center of gravity 100 mm to the right of section 1. Calculate accu- rately the magnitude, direction, and location of the resultant force exerted by the liquid on the nozzle. V=3 m/s 300 mm d 150 mm d

7.73. This nozzle discharges ideal liquid of specific weight 9.80 kN/m³ to the atmosphere. The velocity in the pipe is 3.0 m/s. The velocity through the jet may be assumed to vary linearly from top to bottom. The nozzle is of such shape that the weight of liquid contained therein is 135.0 N, with center of gravity 100 mm to the right of section 1. Calculate accu- rately the magnitude, direction, and location of the resultant force exerted by the liquid on the nozzle. V=3 m/s 300 mm d 150 mm d

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 Ib/ft'. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for mercury equal to 846 and for water equal to 0 62.4 at 68° F. Mercury
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
Water flows steadily through a pipe with ID 35 mm. This pipe expands suddenly to an inner diameter of 75 mm and then stays at that diameter. The flow speed in the 35 mm pipe is 32 m/s. The water gage pressure in the thinner pipe is 510 kPa. 1. What is the pressure at the entrance to the thicker section of the pipe? Is the pressure there larger or smaller than in the thin pipe section?
Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 lb/ft3. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for the mercury equal to 846 and for water equal to 62.4 at 68 0F.
Water in a vertical (i.e., gravitational force of the fluid in the nozzle plays a role, and the elevation change in the Bernoulli's Equation, if needed, should be considered) pipe is charging from an attached bend nozzle into the atmosphere as shown in Fig. 5. The nozzle's weight is 20 kg. The pipe and the nozzle are connected by a flange. The gage pressure of the flow at the flange is 35 kPa when the discharge rate is 0.1 m³/s. The volume of the bending nozzle is 0.012 m³. Calculate the vertical component of the anchoring forcing required to hold the nozzle in place and determine its direction. G= 9.81 m/s². The density of water is 1000 kg/m³. ChatGPT solution: Nozzle 1 Area -0.01 m² P-35 kPa Area -0.025 m² 0.10 ms Figure 5: Q5 35 degree
A vertical venturimeter carries liquid of relative density 0.8 and has inle. and throat diameters of 150 mm and 75 mm respectively. The pressure connection at the throat is 150 mm above that at the inlet. If the actual rate of flow is 40 litres/sec and the C 0.96, calculate the pressure difference between inlet and throat N/m?.
Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
If a liquid enters a pipe of diameter d with a velocity, v. what will irs velocity at the exit be if the diameter reduces to 0.5d?
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
1. A pipe 100 mm bore diameter carries oil of density 900 kg/m³ at a rate of 4 kg/s. The pipe reduces to 60 mm bore diameter and rises 120 m in altitude. The pressure at this point is atmospheric (zero gauge). Assuming no frictional losses, determine: i. The volume/s (4.44 dm³/s) 11. The velocity at each section (0.566 m/s and 1.57 m/s) 1. The pressure at the lower end (1.06 MPa) 2. A pipe 120 mm bore diameter carries water with a head of 3 m. The pipe descends 12 m in altitude and reduces to 80 mm bore diameter. The pressure head at this point is 13 m. The density is 1000 kg/m³. Assuming no losses, determine i. The velocity in the small pipe (7 m/s) ii. The volume flow rate. (35 dm³/s) 3. A horizontal nozzle reduces from 100 mm bore diameter at inlet to 50 mm at exit. It carries liquid of density 1000 kg/m³ at a rate of 0.05 m³/s. The pressure at the wide end is 500 kPa (gauge). Calculate the pressure at the narrow end neglecting friction (196 kPa) 4. A pipe carries oil of density 800…