7.36 and 7.37 Use the virtual work method to determine the vertical deflection at joint C of the frame shown.

Q: Given an adjustment containing the following: Number of Control Stations 1 Number of Unknown…

A:

Q: Topic:Bolted Steel Connection - Civil Engineering   *Use latest NSCP/NSCP 2015 formula to solve…

A: Size of steel plates = 225mm x 10mmRivet diameter = 22mm snug fit in the drilled holeAllowable…

Q: 3. A tee-shaped flexural member is subjected to an internal axial force of 2,200 lb, an internal…

A: Internal axial force = 2200 lbInternal shear force= 1600 lbInternal bending moment= 4000 lb*Note: As…

Q: Oil is conveyed on a 6” diameter pipe, sg=0.8 the velocity is 30ft/s. The pipe diameter narrows to…

A:

Q: In a river 45ft wide, having an average depth of 3.5ft and a mean velocity of 2 fps, a contracted…

A:

Q: 1. Given the truss shown in the figure below: a. Complete the overall free body diagram for the…

A:

Q: A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied…

A: weld size = 8 mmload =200 kN Fu = 483.33 MPaAllowable shearing stress through throat of weld = 145…

Q: 1. Determine the magnitude and location of the overall resultant from point B. 2 kN/m 2 kN/m A 4.5m…

A: The magnitude and location of the overall resultant from point B =?

Q: Compute the reactions for the beam in the given figure. The reaction for the beam at A is RAD The…

A:

Q: Abstract for waste management practices at a recycling plant.

A: We need to write abstract for waste management practices at a recycling plant.

Q: Tim 15′ 1 200 lb B 20' 400 lb 600 lb D 15' 15' E 10' 200 lb F

A: For given arrangement,

Q: 4 m 4 4 m 150 KN -6m 25 kN/m ↓↓↓↓↓ B 10 m-

A:

Q: Suppose that P= 1500 lb. Determine the force in each member of the cantilevered truss. Express your…

A:

Q: Consider the beam and loading with M= 12 kN/m shown in the figure. Vertex M A Parabola 8 m- B…

A:

Q: -12/Compute the flow rate of irrigation water Q to

A:

Q: For the activity on node shown below, find the critical path and the expected duration of the…

A:

Q: A stream 84 ft. wide carries 60 cfs. Determine the resulting head over a Cipolletti weir 3 ft high…

A:

Q: Roles of environmental agency in landfill management

A: The objective of the question is to understand the roles and responsibilities of an environmental…

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

A:

Q: Compute the standard deviation of the data. Report your answer with two decimal places.

A:

Q: WT bracket is connected to a wide flange column with an E. 70 fillet welds as shown in the figure…

A:

Q: Problem V Given the truss below, take P₁= 40KN, P₂= 50KN, P₁-30KN, P₂=40kN, a=2m, h=1.5m. Use the…

A: A truss is given we need to find out the force in member EH, ED, DC, GH

Q: Assuming the data follows a Normal distribution, compute and plot the probability mass function…

A:

Q: You are required to carry out the flexural and shear reinforcement design for the simply supported…

A:

Q: A two-story office building totaling 18783 ft2 is interpreted as a light hazard (200 ft2/sprinkler…

A: The objective of the question is to determine the size of the riser pipe needed for a sprinkler…

Q: Problem 02 Axial compression loads in the first interior column of the structure shown are: 95 kN…

A: Given:-dead load=95kNlive load=50kNwind load=75kNk=0.65To find:-remaining allowance

Q: A wastewater treatment plant uses an activated sludge process to treat 0.2 m3/s of primary effluent.…

A:

Q: Offset Point A Stationing 0.00 Offset 12.6 B 0 + 54.80 34.2 C 1+ 38.88 54.2 D 2+ 13.02 85.4 E…

A: Offset PointABCDEFGStationing0.000 + 54.801 + 38.882 + 13.022 + 98.743 + 47.824 +…

Q: A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of…

A: A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt…

Q: The wheel rolls without slipping with an angular velocity ofw = 17 rad/s. (Figure 1) Figure B 0.6 m…

A:

Q: A 25 cm total consolidation settlement of the two clay layer show in figure p6.1 is expected owing…

A:

Q: Concrete precast buildings are less common in regions where there are earthquakes because: Question…

A: The question is asking why concrete precast buildings are less common in regions where earthquakes…

Q: If the discharge rate of a waste drain line is 601 GPM, what is the smallest pipe size that can be…

A: Rate of Discharge (Q) = 601 GPMMaximum Slope of drain = 1/4 inch per footWe need to calculate the…

Q: The annual daily mean discharge data for USGS 08057000 (Trinity Rv at Dallas, TX) is shown in the…

A: Determine the mean of the data.

Q: 10 N.m 5 N.m 2 m TI 20 N 2.5 m F 30° Calculate moments about O. What value of F is needed to stop it…

A: Determine the value of F is needed to stop it rotating.

Q: The welded girder shown in the accompanying illustration has an external shear VD = 300 k and V₁ =…

A:

Q: Use latest NSCP/NSCP 2015 formula to solve this problem *Use hand written to solve this problem…

A:

Q: The trapezoidal channel is made of brickwork (n = 0.139 ) and slopes at 1:500. Determine the flow…

A: The slope is denoted by So ;n = 0.139area is denoted by A ;perimeter is given by ;

Q: Q1/ Use the following speed data collected from 2-lanes freeway section of 0.5 km under free- flow…

A:

Q: How many zero-force members are in the truss shown belo 15 kips 10' 10' 20 kips HGF

A: Conditions for the zero-force member:If at a joint only 3 members meet, out of which 2 members are…

Q: H. W.: Determine approximately the force in each member of the truss shown in Fig. below. Assume…

A: First, let's label the forces on each member of the truss. We will assume that the diagonals can…

Q: What is the total load on B-1 if the load rate is 80#/ft^2 (B) 24-0" 1-5 8'-0" C12" BRICK WALL 8:0"…

A: Load rate = 80 #/ft2

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

A:

Q: For the retaining wall shown, determine the active force per unit width of the wall using Rankine's…

A:

Q: 8 kips are applied to a 3x8 10-foot column; these are calculated using the governing load…

A:

Q: The timber member of Example 1 is used as a simply supported beam on a 16-ft span carrying a…

A: A simply supported beam of span, L = 16ft is loaded with a UDL of 400lb/ft.The cross-section is b x…

Q: 4. A wooden beam is fabricated from one 2 × 10 and two 2 × 4 pieces of dimension lumber to form the…

A: For the given figure,Beam is simply supported load on beam = 5000 lbLoad transferred by nails in…

Q: 2. For the shown truss, determine the force in members BC, BH, and HC State whether the member is in…

A: Determine the force in members BC, BH and HC of the truss. Let's solve using method of section.

Q: Q4-5/ If the Consumptive Use of the plants cultivated in the farm is 16(mm of water depth/day)…

A:

Q: A W12x72 column is an exterior 1st story column (red circled at gridline C) with strong axis…

A:

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.